Question about Cars & Trucks

Open Question

How do I remove interior door handle 2002 Corsa Utility

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Ad

SOURCE: 1999 Toyota Corolla interior door handle

There's two screws by the handle, pull those out and you'll see how it all connects on the inside. I was able to remove my broken one, and drill a hole into the plastic where it broke and reuse it - it's lasted over 4 years now. 

Posted on Aug 12, 2008

  • 840 Answers

SOURCE: removal of door pad on honda jazz 2006 year model

door pad removal look for little pop outs take the pop outs off and thenremove screw then remove the mirror cover then pull on the bottom of door then pull on the side and then pull off trim up and out then you will see a vapor barrier remove it then you see the inside handlejust acouple of srews /please rate my response thank you very much

Posted on Jan 31, 2009

  • 1986 Answers

SOURCE: need to remove inner rear passenger side door

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

Posted on Nov 05, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inside sliding door handle won't open door


Remove the handle to see if the rod has fallen off.

Mar 03, 2015 | 2002 Ford Windstar

1 Answer

Need to intall new front exterior drivers side door handle on a 2002 Hyundai Elantra GLS


remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

Mar 18, 2014 | Hyundai Motor 2002 Elantra

1 Answer

Interior door handle will not open the door (driver's side). How can I fix this? The interior handle will pull as though it is opening the door but it does nothing to open the door. I have to roll my...


this could be a couple of problems 1 the handle portion that connects to the actuation rod is broken or the actuation rod has popped out of the handle. Either way you will need to remove the door panel to identify the problem.

Apr 22, 2011 | 2002 Isuzu Axiom

1 Answer

How do I remove and replace the right interior door handle on my 2002 Toyota Corolla?


specting you have your new door handle on hand, star by removing philips screw, look at your new door hanle and it has tabs or hooks(some are forward others to the back) well now you know to what direction pull/push the handle to unhook, pull a litle on it until you see a steel rod hooked to handle, take a neddle nose chanel locks and cramped, use a small screw driver to remove clip holding rod, now intall new handle back tracking.
good luck

Mar 14, 2011 | 2002 Toyota Corolla

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

How do I change the outside driver's door handle on my 2005 Nissan Altima


You have to remove the interior door panel and look up inside the interior of the door near the door handle and you will see the fasteners. There will be a rod too that has to be removed that goes to the latch. I would also highly recommend that you get a good repair manual for your vehicle. These manuals help walk you through though repairs. Good luck with it.

Dec 18, 2010 | 2002 Nissan Altima

1 Answer

Rightside interior door handle not opening door


It could mean the rod connecting the handle to the latch has broken. You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. and you can access the innards of the door

Sep 04, 2009 | 2002 Kia Sedona

1 Answer

Vehicle problem


you'll need to remove your door panel (screws are by the door handle, arm rest, under door and side of door) and then unhook the handle from the linkage

Aug 10, 2009 | 2002 Audi A6

1 Answer

Interior door handle doesn't work. interior door panel pop off to reconect ?


yes there are screws in several places along the edges of the door panel and in or below the center handle and push pops you have to pull the panel from the edges after removing all screws only then can the truth be revealed

May 18, 2009 | 2002 Honda Civic

4 Answers

Door handle broken (rear left)


broken right rear door handle on 2002 chev impala

Sep 09, 2008 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...