Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!
Posted on Jan 27, 2009
There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.
Posted on Dec 31, 2008
Depends on where you live in the country. In TN where I live most people just use 10W30 all year, but if you live in a colder area you would use 10W30 in the summer and 5W30 in the winter. Hope this helps. Thanks for an honest rating.
Posted on May 19, 2009
Tips for a great answer:
Aug 15, 2014 | 2002 Kia Sportage
May 14, 2014 | 2001 Kia Sephia
Apr 17, 2014 | 2005 Kia Amanti
Feb 09, 2014 | 2000 Kia Sportage
How to replace Oil Pressure Sensor on 2008 Honda Odyssey?
2004 Chevrolet Express Van: Oil pressure sending unit replacing? http://whoisbyme.blogspot.in/2012/06/2004-chevrolet-express-van-oil-pressure.html
HOW TO REPLACE AN OIL PUMP
HOW TO CHANGE ENGINE OIL AND FILTER
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
Check Differential Oil Leaks and Replace Oil
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
HOW TO RESET OIL CHANGE INDICATOR? http://whoisbyme.blogspot.in/2012/07/how-to-reset-oil-change-indicator.html
These details will help.
Nov 25, 2012 | Cars & Trucks
Nov 30, 2011 | 2005 Kia Sportage
Oct 06, 2010 | 2007 Kia Amanti Sedan
Oct 20, 2009 | 2005 Kia Amanti
Nov 21, 2017 | Chrysler 300M Cars & Trucks
82 people viewed this question
Usually answered in minutes!