Question about Cars & Trucks

Open Question

Cylinder head torque setting 5vzfe prado 3.4 v6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

Ad
  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Cylinder head torque specs for kia carnival 2002 2.5 v6


cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.

Jul 03, 2012 | Kia Carnival Cars & Trucks

1 Answer

Hi.i need the torque settings for the cylinder head on a toyota prado 3.0td.thanks


12-point bolt head

step 1. 33 ft lbs.

step 2. additinol 90 degrees.

step 3. additinol 90 degrees.


6-point bolt head.

30 ft lbs.

Apr 15, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

What are the torque settings for a 1997 audi a3 1.6 cylinder head


The torque settings for a 1997 Audi A3 1.6 cylinder head:

1. Tightening sequence
tdisline_167.jpg
2. Cylinder head instructions:
2.1. Renew bolts: Yes.

3. Tightening torques:
3.1. Stage 1 - Tighten: 40 Nm.
3.2. Stage 2 - Tighten: 90 degrees.
3.3. Stage 3 - Tighten: 90 degrees.


Please do rate my response. Thanks!

Jan 22, 2011 | Audi A3 Cars & Trucks

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Head bolt torques spec


3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Jul 07, 2010 | 1999 Buick LeSabre

1 Answer

1994 buick lesabre limited connecting rods torque and head torque


3.8L V6

connecting rod torque

step 1 20 ft lbs.

step 2 an additional 50 degrees

cylinder head torque

step 1 35 ft lbs.

step 2 an additional 130 degrees

step 3. 4 center bolts an additional 30 degrees

May 14, 2010 | 1994 Buick LeSabre

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...