Question about Cars & Trucks

1 Answer

Reset the control panel on the Maytag dishwasher model MDB4409PAB0

Lights are flashing will not start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 133 Answers

You can use obdii scanner to check the engine system, maybe it got fault codes.

Posted on Jul 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the flashing system charging light?


you have a shorted diode or internal voltage regulator problem ! Is the check engine light on ? This charging system is computer controlled ! Don't just change it have it checked !

Apr 09, 2015 | 2010 Mazda 6 2.2

1 Answer

How do I unlock my dishwasher door?


To avoid damaging the mechanism, you must remove the cover of the dishwasher and with a screwdriver blade can unlock the door from inside.

Jul 04, 2013 | Cars & Trucks

1 Answer

All control panel warning lights flashing and headlights flashing on and off.


The ALARM HAS been triggered and so it is important to reset the alarm or else it will drain off the battery. If you can find the reset switch press down and put the key into the main switch to start the car. It must now reset if not repeat.
if none works then remove the battery terminal and check for the alarm settings/reset switch.

Jul 28, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

How to turn change oil light


iI you mean 'how to turn change oil light off" go to fuse panel. Open drivers door there is a panel cover on the side of dash board, remove cover there is a red RESET button that resets oil pressure and tire pressure. Turn the ignition key to the on position but don't start the car. Now press and release the reset button the change oil light should start to flash, now press and hold the reset button until you hear chimming hold until chimming stops then release, the change oil light should go off. If you need to reset tire pressure press reset button twice, the first push will make the change oil light flash the second press will make the tire pressure light flash then hold untill chimming stops, light should go out . Hope this helps.

Sep 30, 2010 | 2000 Pontiac Grand Am GT

1 Answer

How to rest oil change/tire


In the fuse panel located by the drivers side door on the dash is a red rest button.Push that button until the desired light starts flashing oil/tire pressure.Once the light starts flashing hold the reset down for about 10 seconds this should reset the light.

Jun 03, 2010 | 2001 Pontiac Grand Am SE

1 Answer

98 Dodge Caravan-why are the led lights on the AC control panel flashing?


The blinking lights in the rear wiper rear defrost area can be reset by holding 2 buttons of the 3 on the left hand side. The top and bottom buttons. Turn the key on and hold them for about 10 sec and they should start flashing differently. Just let it do this. After they start flashing different. It will take 5 to 10 mins. Then one or more will quit flashing all together. If they don't after about 20 min reset them again it can take about 5 trys sometimes before they all go out.

Feb 21, 2010 | 1998 Dodge Caravan

1 Answer

Traction contol, Transmission, Tire pressers sensor


I'm fighting problem #1 right now myself... I'll let you know if I find an answer.

Anytime you get the Low Tire Pressure light you have to reset it. There is a panel on the driver's side of the dash, facing the door. So you have to have your door open to get to it.You are looking for the red button.


From the 1999 Alero manual:

"To reset(calibrate) the system, turn the ignition switch to ON. The RESET button is located inside the drivers side fuse panel. Press and release the RESET button.

The CHANGE OIL light will begin to flash. Press and release the RESET button again. The CHANGE OIL light will go off, and the LOW TIRE PRESSURE light will start flashing. When the LOW TIRE PRESSURE light is flashing, press and hold the RESET button until the chime sounds."

Apr 25, 2009 | 1999 Oldsmobile Alero

4 Answers

2007 Volvo S80 V8 Sedan Service reset light


Install remote/key into socket.  Push and hold trip button on instrument cluster with all doors shut.  Push start button one time for key position one while holding trip button and count to five.  keep holding trip button and hit start button to key position two where all the warning lites come on the instrument cluster while still holding trip button.  Count to around ten and triangular warning lite should flash. Release button and remove key and then start engine.  May take a few attempts to reset this lite.  

Mar 30, 2009 | 2007 Volvo S80 V8 Sedan

1 Answer

Need to reset flashing instrument lights


Here's what i found is supposed to work.

1. Set blower to HIGH
2. Set mode position to PANEL (AC vent air)
3. Open all AC outlets
4. Temp. on full cold
5. Start engine
6. Push WASH and REAR WIPER switches for 5 seconds until all panel lights are on solid
System will then go through it's paces as it calibrates the climate controls
7. When calibration is complete only the REAR WIPER switch/light should be flashing. Press this switch to extinguish the light
and all should work normally.

Mar 26, 2009 | 1998 Plymouth Voyager

3 Answers

Change oil light remains on after oil change and light over license plate does not work after bulb change


To reset the Change Oil Light: Open driver's door and open fuse access panel
Turn ignition key to on (don't crank the starter) Push reset button located in fuse panel When Change Oil Light starts to flash Press and hold reset button until it beeps and light goes off Repace panel

Jul 17, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...