Question about 2001 Honda S2000

3 Answers

2001 honda s2000 cranks but won't start. Just

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 12,223 Answers

See the diagram attached. by pass the starter and try IT. God bless you
2001 honda s2000 cranks but won't start. Just - 9e5275c8-765d-4a61-8b54-66b1aa02a7d9.jpg88fd4150-50f6-44af-ae57-d52b50579d17.gif

Posted on Jul 18, 2013

  • Marcus Jackson Jul 18, 2013

    Hi Ernesto. Thanks for the response. The starter is working fine. With the cam sensor plugged in, the vehicle just cranks. When I unplug it, it will start, I have to tap the gas pedal to keep it running, let off the gas and it dies

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 615 Answers

If it's cranking, the battery is good. Check the air filter to be sure it's getting air. Check fuel supply to be sure it's getting fuel. Next would be a possible timing issue - harder to check.

Posted on Apr 03, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 2,899 Answers

Might be a weak battery.

Check the battery like this:
Turn on the headlights, then try to start the car.
If the headlights do not dim or go out, then the battery is likely ok.
Check that the battery cable plus post, goes to the starter, Minus post to a good ground, like the engine.
If wiring is ok, then look at the starter solenoid for a good connection.
Problem is most likely the Solenoid or starting relay, whichever the car uses.
Hope this helps.

Posted on Apr 03, 2015

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 215 Answers

SOURCE: 1995 honda civic d15b7 cranks but wont start. new

Are you sure you have correct timing? its definetly a fule problem, if timing is good then turn your key to the on position and try to listin for the fule pump to prime. While the key is in on position go to fuel rail, there is a valve on fule rail called sharader valve. Get a small screw driver and press valve in to check if car has fule pressure. if pressure is present then it is incorrect timing or possible bad cam sensor.

Posted on Mar 01, 2010

bogdanodwazn
  • 5642 Answers

SOURCE: 2001 oldsmobile alero starts but wont stay running just had new gaskets valve and intake,two heads, cam sensor put on it . what could be causing it to crank but then die

check fuel filter,vacuum leak,fuel pump.

Posted on Feb 24, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2001 dodge neon cranked without the cam sensor connected. what's wrong with this picture?


Changing the Cam Position Sensor on Dodge Neon ...

? 10:33
https://www.youtube.com/watch?v=ciCPQ0kVAQY
Dec 21, 2012 - Uploaded by VeeTheAmazingGreek
... had to change out the cam position sensor on my 2001 Dodge Neon. ... 1997 Dodge Neon no start, crank sensor problems - Duration: 26:53.

Dodge Neon Questions - It will turn over but has no spark ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusAug 9, 2015 - I did have a neon while ago and image crank sensor was bad ... my 1999dodge neon has no spark it will turn over but not fire i have changed the crank sensorcoil ... I have a 2001 Dodge Neon 2.0 with 140,000 kms on it.

Dodge Neon Questions - 2001 Dodge Neon will turn over ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusJan 7, 2013 - I have a 2001 Dodge Neon 2.0 with 140000 kms o... ... went about a month before this recent problem, fixed that with no problem now this. ... firing. you said you replaced the cam sensor, did you do the crank sensor as well? ... My 1996Dodge Neon won't stay running whenever I take my foot off of the gas.

Starting Issues and Trouble Code Due to Defective Cam ...

repairpal.com > Problems > Dodge > Neon

Feb 05, 2016 | 2001 Dodge Neon

1 Answer

No spark I believe?


the valves can be open if the cam is still in the head, if you remove the cam and any of the valves are open they are probably bent, this can happen if the timing belt is out of time the pistons hit the valves, if that's the case have the valves replaced and check the heads for damage, the replace head and new timing belt, making sure the timing is correct

Oct 30, 2015 | 1999 Honda Civic

1 Answer

Where is the crank trigger located on a 98 Honda civic dx 1.6 sohc engine,Thanks


The crank and cam sensors are integrated into the coil / distributor assembly.
>

Feb 19, 2015 | 1998 Honda Civic

1 Answer

Changed head gasket, now won't start.


I would need to know the actual code numbers to comment, but in general those components would not keep the engine from starting.
Have you checked compression, spark and fuel pressure ?

Jun 09, 2013 | 2001 Chevrolet Cavalier

1 Answer

92 jeep wrangler 4 cyl 5 speed skipping and bogging down idling rough replaced fuel pump/filter injector o rings fuel pressure regulator timing chain distributor plugs wires map sensor crank sensor idle...


Have you checked the cam sensor? Also does that vehicle have a "throttle position sensor"? Some cars use both MAP and MAF sensors, not sure about your particular vehicle but if it is one of those, cleaning the MAF wouldn't hurt. Good luck.

Jun 28, 2012 | Cars & Trucks

1 Answer

My husband is trying to fix my 04 dodge ram 1500 4.7l, the computer says to replace the crank sensor and or cam sensor. the crank sensor was replaced a month ago. it wont stay running. but he doesnt know...


On the 4.7L, the cam position sensor is located on the right cylinder head (thats the passenger side) toward the front below the valve cover gasket. Not on the front of the head but on the side where the exhaust manifold is attched at the forward end of the head. The crankshaft position sensor is located on the same side (right) but is at the opposite end of the engine between the bell housing and the block. The crankshaft position sensor can be replaced without removing the engine or transmission, it just looks tight. Also, on the crankshaft position sensor, it slides out of a rubber gromet. Here's a few pics to help. hotrodshop.gifhotrodshop_0.gif

Apr 17, 2011 | 2004 Dodge Ram 1500

1 Answer

My check engine light is on and I've been told it is the cam sensor, but I can't find one. It's a 2005 nissan altima. Do they have a cam sensor and a crank sensor?


This engine has both. Nissan recommends replacing them at the same time, I think your local Nissan dealer will tell you the same thing.The cam and crank sensors are in the rear of the engine.Looking from the drivers fender find the right rear corner of the valve cover and look straight down the back of the head. the cam sensor is 3-4 inches down from the valve cover gasket surface.the crank sensor is basically straight down from the cam sensor but much harder to see. it is just above the oil pan gasket surface...

Mar 29, 2010 | 2005 Nissan Altima

1 Answer

1995 honda civic d15b7 cranks but wont start. new


Are you sure you have correct timing? its definetly a fule problem, if timing is good then turn your key to the on position and try to listin for the fule pump to prime. While the key is in on position go to fuel rail, there is a valve on fule rail called sharader valve. Get a small screw driver and press valve in to check if car has fule pressure. if pressure is present then it is incorrect timing or possible bad cam sensor.

Mar 01, 2010 | 1995 Honda Civic

Not finding what you are looking for?
2001 Honda S2000 Logo

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...