Question about Cars & Trucks

Open Question

Mimium height 240 volt batten holder on a vertical wall

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to aim headlights-2002 forester


ALL headlights have vertical and horizontal adjustments. The vertical may be obvious, an M8 shaft. Horizontal may be non obvious, or the adjuster is covered with a rubber grommet. Once you've located the adjusters, find a wall eve on mall car park, and see the low beam to the same height. Check high beam, and a just the horizontal as needed.

May 23, 2014 | 2006 Subaru Forester

1 Answer

Brick wall crack


Check for rusted body parts,suspension mounts etc

May have to replace the springs

Shocks have nothing to do with ride height

Apr 23, 2014 | 1991 Volvo 240

1 Answer

How do you remove the headlight assembly on 1995 ford f250?



  • 1.
    Remove the two upper screws from the headlight housing, using a Phillips screwdriver.
  • .
    Locate the two lower retaining nuts inside the engine compartment at the bottom of the headlight housing. Remove the nuts using a ratchet, extension and socket.
  • Separate the turn signal and marker light assembly from the front grill. Rotate the bulb holders counterclockwise and pull them out of the assembly. Set the assembly aside.
  • Unplug the headlight bulb connector from the bulb. Rotate the retaining ring counterclockwise one-eighth turn and remove it from the housing. Pull the headlight bulb straight back and out of the housing. Do not rotate the bulb during disassembly.
  • Lift up on the headlight housing retaining clips to unsnap them from the headlight housing vertical adjuster studs.
  • Locate the horizontal adjuster at the outer bottom corner of the headlight assembly inside the engine compartment. Loosen the horizontal adjuster until it is free of the adjuster nut.
  • Remove the headlight housing from the vehicle.
Installation
  • Install the headlight housing in the front grill.
  • Engage the horizontal adjuster screw with the adjuster nut and screw it partially in.
  • Snap the headlight housing clips on the vertical headlight adjuster studs.
  • Insert the headlight bulb into the headlight housing, flat side up. Slightly rotate the headlight bulb to engage the grooves in the light with the alignment tabs in the back of the housing. Install the retaining ring on the bulb. Plug in the headlight bulb connector.
  • Install the bulb holders in the turn signal and marker light assembly. Install the assembly in the grill. Install the two upper screws, using a Phillips screwdriver. Install the two lower retaining nuts, using a ratchet, extension and socket.
Headlight Aiming
  • Pull the vehicle to within a few inches of a blank wall, on a flat surface. Apply two strips of tape to the wall vertically to mark the centers of the headlights. Apply a strip of tape to the wall horizontally to mark the center of the headlight height. Back the vehicle up 25 feet in a straight line.
  • Turn the headlight low beams to the "On" position.
  • Adjust the vertical headlight adjusters until the high-intensity zone of the light pattern is two inches below the horizontal mark on the wall.
  • Adjust the horizontal headlight adjusters until the high-intensity zone of the light pattern is two inches to the right of the vertical headlight marks on the wall.

Nov 08, 2012 | Cars & Trucks

1 Answer

We need instructions on adjusting the headlights on a Mitsubishi Lancer 2002


Aiming
  1. Park the vehicle on level ground, so it is perpendicular to and, facing a flat wall about 25 ft. (7.6m) away.
  2. Remove any stone shields, if equipped, and switch ON the lights.
  3. Loosen the mounting hardware of the lights so you can aim them as follows:

  1. The horizontal distance between the light beams on the wall should be the same as between the lights themselves.
  2. The vertical height of the light beams above the ground should be 4 in. (10cm) less than the distance between the ground and the center of the lamp lenses for fog lights. For driving lights, the vertical height should be even with the distance between the ground and the center of the lamp.

  1. Tighten the mounting hardware.
  2. Test to make sure the lights work correctly, and the light pattern is even.

Dec 23, 2010 | 2002 Mitsubishi Lancer

1 Answer

How do you replace the battery on a pontiac grand am 2003? I allready have the right battery.


Welcome to FIxYa.com



REMOVAL PROCEDURE


1. Disconnect the negative battery cable.

2. Disconnect the positive batten- cable.

3. Remove the batten' hold down retainer.

4. Remove the batten'.

IMPORTANT: Do not tip the batten' more than 40 degrees dining removal.

INSTALLATION PROCEDURE


1. Install the batten' to the battery tray.

IMPORTANT: Do not tip the batten' more than 40 degrees during batten' installation.

2. Install the batten' hold down retainer.

3. Connect the positive battery cable.

Tighten the cable bolt to 15 N.m (11 lb ft).

4. Connect the negative batten- cable bolt.

leedavidian_2.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Nov 18, 2010 | 2003 Pontiac Grand Am

1 Answer

I just installed the right head light on a 2000 f250. I'm trying to find the specifications on distance and height of the light beams, L &R when adjusting the lights.


Headlamp Adjustment —Screen Method Aiming NOTE: Horizontal aim is not necessary for this vehicle and is not adjustable.
NOTE: Consult your state's vehicle inspection manual for recommended tolerance ranges for visual aiming.
  1. NOTE: The sight shield may need to be positioned or removed for access to the adjusters.
    Before starting headlamp assembly adjustment:
    • Check the tire inflation.
    • Check that no other load is in the vehicle other than a half tank of gas.
    • Check that the headlamps are clean.
    • Check for correct headlamp operation.
    • Check that the vehicle is on level ground.
    • If the vehicle is equipped with air suspension, make sure the switch is on.
    • NOTE: The vertical wall or screen must be a minimum of 2.4 meters (8 feet) wide.
  2. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from the vertical wall or screen directly in front of it.
  3. e4d4fd8.gif
    NOTE: The center of the lamp is marked by a 3 mm (0.12 in) circle on the headlamp lens.
    Mark a horizontal reference line on the vertical wall or screen.
    1. Measure the center of the headlamp height to ground and record.
    1. Make a 2.4 meters (8 feet) horizontal mark (masking tape) on the vertical wall or screen at the same distance from the ground as previously recorded.

d505709.gif
  1. NOTE: This procedure should be done in a dark environment to effectively see the headlamp beam pattern.
    Turn on the low beam headlamps to illuminate the wall or screen and open the hood.
  1. NOTE: The appearance of the beam pattern may vary between vehicles.
    On the wall or screen, locate the high intensity area of the beam pattern.

7ced4e6.gif NOTE: The appearance of the beam pattern may vary between vehicles.
Identify at the top edge of this high intensity area a distinct horizontal cutoff in the beam pattern. If the top edge of this cutoff is not even with the horizontal reference line, the headlamp beam will need to be adjusted.

1fb716f.gif

Apr 06, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

How do you adjust a headlight from pointing up to the right height


VERTICAL AIM ADJUSTMENT
1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)
from a vertical wall or screen directly in front of it.

2. Measure the height from the
center of your headlamp to the
ground and mark a 2.4 meter (8
foot) horizontal reference line on
the vertical wall or screen at this
height (a piece of masking tape
works well). The center of the lamp
is marked by a 3.0 mm circle on the
headlamp lens.

3. Turn on the low beam headlamps to illuminate the wall or screen and
open the hood.

4. On the wall or screen you will
observe a light pattern with a
distinct horizontal edge of high
intensity light with a slight angle
towards the right. If this edge is not
at the horizontal reference line, the
beam will need to be adjusted.

5. Locate the vertical adjuster on
each headlamp, then use a 4 mm
socket/wrench to turn the adjuster
either counterclockwise (to adjust
down) or clockwise (to adjust up)
aligning the upper edge of the light
pattern up to the horizontal line
.
6. HORIZONTAL AIM IS NOT
REQUIRED FOR THIS VEHICLE
AND IS NON-ADJUSTABLE.

Mar 09, 2010 | 2002 Ford Explorer

3 Answers

WHAT ARE THE SPECS TO ALIGN Headlights for 2006 chevy colorado


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 06, 2009 | 2006 Chevrolet Colorado

1 Answer

How do I adjust the height of headlights on a 1998 Landcruiser?


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 29, 2009 | 1998 Toyota Land Cruiser

1 Answer

Headlight adjustment 1999 S70


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Aug 18, 2008 | 1999 Volvo S70

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...