Question about 2002 Kia Rio

Open Question

Obd port location kia rio - 2002 Kia Rio

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: kia rio 2001 thermostat

Fallow the "UPPER" Radiator Hose from the Radiator to the Engine Cylinder Head, The Thermostat Housing is the Unit that the UPPER Radiator Hose Connects to. Theres is 1 BOLT (TOP) & 1 NUT (BOTTOM) that you Remove to Gain Access to the Thermostat itself. Hoping this Helps you out There . Have A Great Day.

Posted on Feb 09, 2009

Ad
  • 176 Answers

SOURCE: need to know where knock sensor is located on a 2001 kia rio.

At center rear of engine compartment, by intake manifold support bracket.

Posted on Dec 23, 2009

arauzvictor1
  • 466 Answers

SOURCE: knock sensor replacement

Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Posted on Mar 19, 2010

  • 10 Answers

SOURCE: gear box oil filler plug - kia rio

you have to take off the speedometer cable/wiring harness from the top of the trans and fill it from there....one 10mm bolt...very awkward spot...it might be snug, so just take a flat head screwdriver from underneath to tap it loose...

Posted on May 14, 2010

emissionwiz
  • 76630 Answers

SOURCE: where is located the obd II port for kia sephia 1995

Under the dash in front of the driver. See picture below
8_23_2012_10_27_01_pm.jpg

Posted on Aug 23, 2012

Testimonial: "Found it, thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spark plugs stop sparking after 4 revalutions on my 2004 kia rio


Check the crank shaft sensor !? Connect OBD 2 scan to read the error memory

Jul 21, 2014 | 2004 Kia Rio

1 Answer

What is mil circuit malfunction kia rio 03


Mil stands for malfunction indicator light or lamp or CEL , check I engine light.... Hook up obd and pull codes.

Apr 05, 2014 | 2003 Kia Rio

1 Answer

Replace starter on 2006 kia rio


WHERE IS STARTER LOCATED AT ON A 2006 KIA RIO

Nov 21, 2012 | 2006 Kia Rio

1 Answer

Obd ll code p1693ona kia rio 2003


that code is manufacturer control auxiliary inputs auxiliary outputs

Oct 13, 2012 | 2003 Kia Rio

2 Answers

What is a kia rio p1800 error code mean?


the code is for engine torque signal malfunction.its either a short to voltage or ground in between engine computer and transmission computer. or a bad trans computer [tcm] manuel says check for shorts or bad connections at the connectors from ecm to tcm then states if no wire problems found then try a new tcm and if problem goes away then install new tcm.i know those instructions are lame but it comes from the kia service manuel. there are no tsb or recalls listed for that code. so i would recomend take to dealer because they would have a known good tcm to try.plus if you bought the car new then the 10 year 100,000 mile warranty may still be in effect beings how its a powertrain issue so if less than 100,000 miles and you bought it new it wouldnt hurt to ask them if it might be covered

May 29, 2010 | 2002 Kia Rio

1 Answer

I get the OBD-II codes of P0325 and P0326. I did a search and I found this site http://www.obd-codes.com/p0325 which explains about the knock sensor circuit malfunction. Is the knock sensor, which I read...


Your local auto parts store, or auto parts superstore should have it, if not, be able to order it. Ex.--Advance Auto Parts store has a BWD Knock Sensor, #S8815, for around $50.00. 2002 Kia Rio 1.5L/L4/FI

Apr 02, 2010 | 2002 Kia Rio

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

1 Answer

Need to know where knock sensor is located on a 2001 kia rio.


At center rear of engine compartment, by intake manifold support bracket.

Dec 23, 2009 | 2001 Kia Rio

Not finding what you are looking for?
2002 Kia Rio Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...