Question about Cars & Trucks

Open Question

Head bolt torque setting daihatsu sirion 1998

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

Ad
  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

  • 98 Answers

SOURCE: 1999 Daihatsu Sirion

Your engine is probably an EJ-DE twin cam 12 valve.

Generally Daihatsu belts have marks on them that line up with dimples on the sprockets for the intial phasing. You rotate the engine to top dead centre on No1 piston and install the belt from there. The cams should be not be putting any pressure on the intake and exhaust valves of No1 when phased correctly.

Posted on Oct 10, 2008

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Sirion. What is causing massive amounts of white oily smelling smoke from exhaust?


Did you have the heads checked out? Make sure they weren't cracked internally? Milled flat? If you did all the torque specs. It could only be the heads or a cracked cylinder.

Apr 22, 2016 | Daihatsu Cars & Trucks

1 Answer

How do i get the front drive shafts out so i can replace the engine


it will be held by engine with few bolts
and if no bolt is seen then just lever it out.. with little force.

Oct 03, 2014 | 1998 Daihatsu Sirion

1 Answer

Wheel bearings daihatsu sirion fix


Yes! Easy answer..you DO need something with ooomph! I used a very long lever, ended up lifting the car off the ground! I'm guessing these are the original bearings? they continue (nuts) to tighten.. Don't over tighten the new ones

Feb 28, 2013 | 1998 Daihatsu Sirion 1.3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...