Question about Toyota Cars & Trucks

Open Question

Torque spec transmission pan

1993 Toyota Corolla torque specs for transmission pan

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75744 Answers

SOURCE: Transmission toque specs

The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Posted on Jul 27, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 101 Answers

SOURCE: 1998 Lincoln Mark viii Transmision Pan Torque Specs?

not needed just use a 1/4 inch drive just a bit over hand tight if u need the spec it is 25 inch pounds

Posted on Mar 01, 2009

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 104 Answers

SOURCE: torque for head bolts for 1984 Toyota Corolla

head bolt toque specs are 40-47 ft-lbs

Posted on Apr 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head tightening torques


there are TWO sets of torque specs you need to have, torque them all in sequence to the first then repeat it using the second torque spec. and calling auto zone they should look it up for ya and tell you right over the phone. make sure you get both specs. there isnt just one torque specs, i learned this on a isuzu trooper, lesson learned. lol

Dec 14, 2013 | 1995 Toyota Corolla

1 Answer

Are there torque specs for the transmission pan on a 1993 mercury cougar 3.8 v6


I'm sure that there are torque specs. for this. I just did both pans on my 1999 Mercury Sable with a 3.0 Duratec V6 DOHC with the AX4N transmission and both pans on that are tightened to 7-9 ft.-lbs.
I don't know if this would be the same unless it has an AX4N transmission. I hope this helps.
Good Luck!!!

Aug 01, 2013 | Cars & Trucks

1 Answer

What are the torque specs for transmission pan bolts on 2003 maxima


hello! the torque specs on transmission oil pan are 62 to 80 inch pounds or 7 to 9 newton meters. hope this information helps you!

Sep 17, 2009 | 2003 Nissan Maxima

2 Answers

Torque for head bolts for 1984 Toyota Corolla


head bolt toque specs are 40-47 ft-lbs

Mar 22, 2009 | 1984 Toyota Corolla

1 Answer

Torquing head


The 98 Corolla has a "torque-to-distance" spec.

First, torque all 10 bolts to 36 ft lbs (49 NM or 500kgf-cm), in a clockwise fashion, starting with the 2 center bolts.

Second, mark the bolts with a paint mark, and then torque each of the 10 bolts an additional 90 degrees.

Hope this helps, and thanks for choosing FixYa.

Nov 15, 2008 | 1998 Toyota Corolla

1 Answer

2001 Toyota Echo Wheel Bolt Torque?


Looks like Corolla and Echo have the same spec. 76 ft-lb.

Aug 25, 2008 | 2001 Toyota Echo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...