Question about Cars & Trucks

1 Answer

Town country climate control

Rear blower not working

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Theres a blower back there and either its a fuse or you need a new one

Posted on Jul 18, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: 2005 Town Country front blower motor inop fuse/relay ok

Break Down And Replace The Blower Motor


REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIR-BAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN AN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY OR DEATH OR DEATH.

NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel.
  3. Position the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.
    1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
    2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.
    3. Push the rubber grommet through the opening in the lower air inlet housing.
    4. Route the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
    5. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
    6. Gently flex the recirculation air door downward to gain access to remove the blower motor from the HVAC housing. NOTE: To aid in installation, note the position of the blower motor mounting tabs prior to removal
      1. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as necessary.
      INSTALLATION

      1. Gently flex the recirculation-air door downward to gain access to install the blower motor into the HVAC housing.
      2. Position the blower motor to the HVAC housing and tilt and rotate the blower motor as necessary to install it into the HVAC housing.
      3. Align the blower motor mounting tabs to the locations noted during removal and install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      4. Route the blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet.
      5. Position the recirculation door pivot shaft into the lower air inlet housing and install the inlet housing.
      6. Install the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      7. Install the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing. Tighten the screw to 2 N·m (17 in. lbs.).
      8. Connect the blower motor wire lead connector to the blower motor resistor or power module, depending on application.
      9. Install the recirculation door actuator.
      10. Reposition the carpet.
      11. Install the passenger side cowl trim panel.
      12. Reconnect the negative battery cable.
      13. Perform the heater-A/C control calibration procedure.

Posted on Feb 07, 2009

mkv0525
  • 358 Answers

SOURCE: heat/ac blower motor

ce the resister for blower motor.

Posted on Jun 05, 2009

  • 240 Answers

SOURCE: Front climate control blower only works on high speed.

Replace your blower motor resistor
Resistor located under dash on passenger side in screwed into blower housing. May be able to be repaired. Requires soldering a small piece of "unmelted solder" across where the old fusible link was. look carefully at resistor. Or else just replace. Buy new. Junkyard resistor likely to be as bad as yours.

Posted on Jun 13, 2009

wilsodfarm
  • 986 Answers

SOURCE: blower motor stuck on high! 2001 town &country

your blower resister is bad and you need to replace it.......heres how,The glove box can be lowered all the way out of the way just by pulling in the sides so the rubber stoppers come out toward you. The sides bend easily to allow that.

The glove box being out reveals the resistor in the heating duct right in front of you. Just remove the two sets of wires and two bolts (10mm socket, I think) and the resistor pack slides right out. Then bolt in the new one an plug the wires back in (they only fit in one way). Fold the glove box back up and press the stops in to get them back in place and you are done.

The resistor pack only cost $12 and change at my dealer. It is part number 1-04885583AB which was a replacement for the same number with AA at the end, so I’m guessing they had a lot of trouble with the AAs and so made a better AB.

Last Winter my heater blower fan worked only on High. I changed the front heater/AC blower resistor pack and was surprised at how easy it is, but I had to figure it out for myself since my Dealer's parts guy was no help as to where the part lived and my Haynes manual was just plain wrong. This was on a 2001 T+C. I'd be very surprised if the 2001 Caravan was any different. Don't know what other year vans would be the same. I do know some earlier generations had this resistor under the hood and Haynes had is with the blower sort of behind the instrument cluster.

Posted on Jan 14, 2010

jturcotte
  • 7789 Answers

SOURCE: how to replace rear blower

from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Posted on Nov 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Town country climate control


REMOVE FROM DASH, TAKE OUT CUP HOLDER/ PRY OFF SMALL COVER, BEHIND 2 SMALL SCREWS, THEN FRAME AROUND CLIMATE CONTROL, REMOVE UNIT REMOVE BIG PLUG, REPLACE AND REASSEMBLE

Sep 29, 2013 | 1999 Chrysler Town & Country

1 Answer

Town country climate control


It's the fan resistor that's bad. It's about $20 and 20 minutes to fix (maybe bit longer to get all of the trim off then back on) ask parts house to show you where it is located.

May 27, 2013 | Cars & Trucks

1 Answer

Chrysler town and country blower quite working


Before you go nuts on getting expensive parts check the blower motor resistor(fan speeds go through it) Maybe the thing blew out. also there is a relay for that and a fuse. Yes just the blower.

Oct 28, 2012 | 2003 Chrysler Town & Country

1 Answer

A/C Blower Switch on chrysler----- Blower works in


Chrysler vehicles are notorious for the blower motor resistor going out. If your Town & Country has automatic climate control use a SMP RU399, else use an SMP RU362 for the front resistor and a SMP RU490 for the rear. They are generally located on top of the blower motor/wheel assemblies.

May 26, 2011 | 2003 Chrysler Town & Country

1 Answer

Blower is on high all the time. Seems like the climate control system is not working. Didn't know if there is a blown relay? or a bad sensor?


No none of the above. There is no sensor for the blower and if the relay for the blower motor was blown then the blower won't get voltage hence wont turn on at all. Sounds to me like the climate control is shorted and is not allowing variable resistance to chance speed. Good Luck

Dec 07, 2009 | 2003 Chrysler Town & Country

1 Answer

Front climate control blower only works on high speed.


Replace your blower motor resistor
Resistor located under dash on passenger side in screwed into blower housing. May be able to be repaired. Requires soldering a small piece of "unmelted solder" across where the old fusible link was. look carefully at resistor. Or else just replace. Buy new. Junkyard resistor likely to be as bad as yours.

Jun 13, 2009 | 2002 Chrysler Town & Country

1 Answer

Ac fan stays on high


If you shut off unit and fan still runs, I had the same problem. I needed to replace blower motor resister located behind glove box. 2 plugs and 2 screws to remove. bought off internet for $60.

May 20, 2009 | 2003 Chrysler Town & Country

1 Answer

I've got dual climate in the front, and the front blower just quit working. The rear blower still works. I get just a little air out of the front vents when i'm going 55 mph down the road. Any...


i have a 2005 town-country van had for 7mos, went to use the heat and the blower dose not work, in the pass week i have talk to others that have the same problem one 1999- other was 2004, has there been any recalls on this issuse? thank you harleyma

Jul 31, 2008 | 2005 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...