Question about Cars & Trucks

Open Question

How do I replace a rear brake line on a 2004 chevy silverado

Line is busted & leaking.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Auto Master
  • 139 Answers

SOURCE: 00 Chevy Silverado... ABS EBCM diagram help??? Brake line hookups

Hello,
I hope this helps.






1ec2f93.jpg
Thank You,
Roy

Posted on Aug 28, 2009

SOURCE: leaking brake line

I end to fix it on my way i bough universal brake steel tube and one connector and i disconnect from the rubber flex pipe and cut flash the old pipe one foot from front before fuel tank where old pipe still in good shape i put connector between old pipe and new pipe on back end i put regular universal tube fitting.
works good .

Posted on Aug 29, 2008

  • 113 Answers

SOURCE: Brake Pedal goes to the floor in my 1990 Chevy C1500 Scottsdale

do you have a self bleeder kit? first off, you have to bleed the master cyl back into its self and the combination valve before you go to the wheels. when you do that, I think you will find that you have air in the lines. disconnect both brake lines from the master cyl and put the bleeder kit fittings on the master cyl, then put the rubber tubing with the kit on the fittings and submerge it in the brake reservoir. make sure its full. then pump the pedal until you get a hard pedal. if that is the case, reconnect the lines to the master, then have an assistant pump up the brake pedal with the engine off, and bleed the combination valve which should be connected to the master by steel tubing. pump it up, then hold it down, and crack the fittings loose, one at a time until the pedal goes about half way down, but do not release the brake pedal until the line is tight again, otherwise you will **** air in the lines. after you do all that, go to the farthest caliper or wheel cylynder from the master and bleed that with the same technique,and dont release the pedal until you close the bleeder screw. unless you have a major prob, this will work.

Posted on Jul 20, 2009

  • 347 Answers

SOURCE: Rear brake pad dragging

ADJUST THE BRAKE CLEARANCE ON ALL FOUR WHEELS.

Posted on Jan 01, 2010

  • 111 Answers

SOURCE: replacing rear brake shoes on 2007 silverado 4WD

when you pull the hub off take a picture of the brakes so you can see all the parts, so you can tell where everthing goes back together.

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

.brakes line locateions 1996 gmc 1500


Have to fabricate new brake tubing & just replace the rusted
lines as you see them.

If you get under there & look, you will have your answer

A guess from my experience, would say you start at the proportioning valve & go past the door & leak, to the rear
somewhere at a junction block on the axle housing or to an
abs hcu unit, if one of them there along the way

Sometimes you need to make two lines with a union under the door,
as that is the longest run under a truck & to do one piece may not be
possible & get it in place, with all the bends & things you have to pass

On a 1996, I would suggest you bleed all four corners first
Then remove the master cylinder & clean out the moisture
Then replace All rubber flex hoses
Then replace the entire brake system lines
Once one rusts out, their all months apart & unsafe to use
piece mealing it one section at a time

Apr 09, 2014 | 2002 GMC Sierra 1500

1 Answer

Coolant leaking


Sounds like a heater core seal busted, check if you got water leaking into the passengers floor. If so, you got a bad heater core

Dec 26, 2013 | 1994 Pontiac Grand Am

1 Answer

01 duramax died fuel leaking rear left side of engine


sounds like a busted fuel line. check your fuel rail and lines.

Feb 17, 2013 | 2000 Chevrolet 2500

1 Answer

My power steering fluid is leaking, i fill it up and it all leaks out does this mean the the hose is busted or the power steering gear is no good, yet when i fill it back up with power steering fluid it...


The most common cause is a leak in the power steering line. With someone sitting in the car,(and the car running) watch the power steering line and ask them to turn the wheel in both directions. A leak in the power steering line will spurt fluid during this exercise whereas a leak in the power steering unit itself would tend to ooze fluid due to less pressure.

Apr 27, 2011 | 2005 Dodge SRT-4

2 Answers

Leaking Gas on left side of gas tank, can't tell if it's the line


More than likely you have a busted fuel line, or one of the connections from the fuel lines to the fuel pump is broken. If you know how to repair cars, drop the tank and find the leak. If you don't know how, have the vehicle towed to a shop. Driving the car would definitely be a fire hazard.

Jan 24, 2010 | 2001 Chevrolet Impala

1 Answer

All tranny fluild leaked out and car will not drive


Busted tranny line , pumped all fluid out. Tranny won't work without fluid.

Jan 18, 2010 | 2000 Hyundai Sonata

1 Answer

BLEEDER VAULVE LEAKING . I REPLACED THE CALIPER ONTHE PASS SIDE BECAUSE PISTON BUSTED IN HALF PLUS REPLACED PADS, HOWEVER WHEN ATTACHING THE BRAKE LINE/BLEEDER IT LEAKS. NOT SURE IF I AM ATTACHING IT...


If the bleeder screw is leaking, pull it out an carefully inpsect for damage or scoring...

If bleeder screw, replace it, if caliper is damaged, replace that.

the bleeder screw should have nothing to do with the brake line attachment.

Sep 21, 2009 | 1990 Mercury Grand Marquis

2 Answers

Busted brake line ---trying to figure out which one is broke---- it's one in the back ----clusterd together w/ the fuel lines on the drivers side


Jack it up, use safety stands, & hit brakes to see where leak is, with safety glasses on, to avoid fluid in eye.

Jul 22, 2009 | 1998 Ford Escort

1 Answer

White Smoke coming out of bonnet & exhaust,stinks of burning oil


oxygen sensor
oil leak at back of block thats spirting on hot engine block
bad oil rings in block
valves bad
head or head gasket worn and cracked check the oil if chocolate brown then this would be it
a/c preasure line busted or a/c locked up
water line busted on hot engine or small water leak
bad emmission components

these are the things i can think of off the top of my that could give this reaction in vehicle since im not there in person to see vehicle this will have to be what i think

Jun 16, 2008 | 1990 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...