Question about 2002 Ford Taurus

1 Answer

Ses oil light is on just after replacing camshaft senosr

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 21,873 Answers

Do you know if the wire going to the oil pressure switch is plugged in ? And not grounded anywhere ?

Posted on Jul 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 f250 5.4 3 valve no codes no flashing SES lightruns with bank 2 completely dead does not hit on 5 6 7 8 cylinders


Timing chain possible . But more likely Camshaft Phaser for the variable valve timing , do you change you oil regularly ,these can get clogged up . They are controlled by oil pressure.
Variable Camshaft Timing (VCT) System The VCT system consists of an electric hydraulic positioning control solenoid, a camshaft position (CMP) sensor, and a trigger wheel. The CMP trigger wheel has a number of equally spaced teeth equal to the number (n) of cylinders on a bank plus one extra tooth (n+1). Four cylinder and V8 engines use a CMP 4+1 tooth trigger wheel. V6 engines use a CMP 3+1 tooth trigger wheel. The extra tooth placed between the equally spaced teeth represents the CMP signal for that bank. A crankshaft position sensor (CKP) provides the PCM with crankshaft positioning information in 10 degree increments. The cam timing can become advanced to much an cause a low compression problem. You could do a compression test an that would tell you. this vehicle should have at lest 150 psi .

Jan 20, 2015 | Cars & Trucks

1 Answer

Check engine light comes on 2006 altima 2.5


check all fliud levels antifreeze/oil/power steering/ transmission/even washer fluid.. as some have level switches on them.. these will cause your light to activae also..

Dec 26, 2013 | 2006 Nissan Altima 2.5

1 Answer

Both cam sensors replaced for ses/vdc/slip lights, hard starting when hot, still have ses light, rough idle at stops, smooths out when driving


First thing I would do is check oil level. If its low fill to correct level. retry. Low oil level will cause cam actuators to stick & your problem can happen with SES light. Second I would make sure you got updated cam sensors from dealer. El-****-o sensors can cause this problem also. Third off If you can fined out what the codes are in the PCM...... Nissan ignition coils that start to go bad will do this also. Throttle body that wast or lost its programmed learn can do this also.... So please see what codes are stored will help the way to look.

Sep 03, 2011 | 2003 Nissan Murano

1 Answer

I have a 1999 BMW 740il I hooked up my OBD code reader and the that came up was p0340. I found out what it ment. I went to the BMW parts department and bought new camshaft sensor and replaced them. Now my...


  • There are two Camshaft position sensors. The one this is for is the one by the oil dipstick on the LH side of the engine. If you replaced the other you need to replace this one as well. Both are recommended, in other words when changing one it is recommended to change the other as well.
  • If you have any further questions or comments please feel free to ask and thank you for using FixYa.
  • That being said I sat in a chat and waited for a response from you for 12 minutes. I hope this answers your question.

Regards, Tony

Jun 13, 2011 | BMW 7 Series Cars & Trucks

2 Answers

Can u tell me what the problem of this code PO340


I have a 1999 BMW 740 il My SES light came on so I hooked up my OBD code reader p0340 - Camshaft Position Sensor Circuit Malfunction is what came up. so I went to the BMW parts department and bought the Camshaft Position Sensor.
I Replaced the with the new. My SES light was still on so I hooked up the OBD reader again hoping it may reset my SES light but it didn't what did happen is the OBD reader came up with the same code (p0340 - Camshaft Position Sensor Circuit Malfunction) witch is what I just replaced. now I'm at a loss. I'm not sure how to reset my SES light and if I just replaced the Camshaft Position Sensor why dose it the OBD code p0340 still come up. Any suggestions?

Mar 18, 2011 | 1996 Nissan Altima

1 Answer

1997 Aurora: it takes a long time to start...


is the SES light on? if so its probably a camshaft position sensor or crankshaft sensor, relatively easy to replace.

May 18, 2010 | 1997 Oldsmobile Aurora

1 Answer

Where is the camshaft position senosr


Hi it is behind the cam cover below the cam pulley wheel.

It does depend on the model but once the cam cover is removed you will be able to see it quite easily.

Hope this helps, if not please get back to me with engine size etc
Regards
Dan

Feb 21, 2010 | 1998 Plymouth Voyager

1 Answer

ENGINE OIL LIGHT


The engine oil light measures oil pressure rather than volume. The senosr couldf be bad or your oil pump could be failing

May 15, 2009 | 1993 BMW 5 Series

1 Answer

Crankshaft and camshaft position sensors


MAke sure you replaced the right sensor and it's the proper design.(If you bought a generic part, it;s probably the wrong thing) I replaced my cam and crank sensors with the generic ones from AutoZone and they had no effect. Took it to Nissan, they replaced both at my expense, AND REPROGRAMMED THE ECU. That fixed that problem SES light hasn;t come on in 6 months....Fingers crossed

Mar 10, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2002 Ford Taurus Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...