Question about Cars & Trucks

Open Question

Nissan NP200 2006 Torque specks

Head was sent to engineering need torque specks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: torque specks

hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right

Posted on Feb 12, 2009

SOURCE: head bolt torque settings for 720 nissan cab 2

dear friend-your torque setting on the 720 is the same as the L18 and is set at 85 - 90 nm.

Posted on Jul 23, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

ghost45
  • 1280 Answers

SOURCE: how much to torque 2003 nissan altime head - Sequence

Buy the service manual (or the Chilton's Manual at AUTO ZONE, PEP BOYS, O'RIELLY'S, CAR QUEST, etc.).

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque specs for a v8 3.6 evinrude heads


Many torque specs can be transposed. the key is to know what other similar models are there. A torque speck is the safe limit to witch to tighten a bolt. so if you can find the similar torque on a similar engine that does not seem too high I would start there. if it is an all cast iron engine I would try 95 foot LBS but is it is Aluminum I probably would not go over 25. Just saying. the torque is also directly related to the compression of the engine and the compression is directly related to the octane required, if you are not required to burn high octane then you have a low compression engine and most likely a low torque speck and if it is an aluminum head and block the very more likely very low torque.
best of luck

Apr 12, 2015 | Cars & Trucks

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

1 Answer

Final torque settings for nissan navara d22 diesel engine cylinder head


You do not need to re-torque modern cylinder heads. That went out withe Buffalo.

Nov 07, 2012 | Nissan Cars & Trucks

1 Answer

Engine head bolts


most automotive parts suppliers will offer you the torque specks and sequance of torque just call them

Jul 20, 2012 | Jeep Cars & Trucks

1 Answer

What is the torque of nissan urvan qr25 engine head bolts


nissan urvan 2006 engine head bolt torqe

Jan 31, 2012 | Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

I need torque specks for valve train for a 1987 nissan truk v6 3.0 litter


cylinder head bolts 40 - 47 ft lbs, intake manifold bolts 12 - 14 ft lbs. , intake manifold nuts 17 - 20 ft lbs. , rocker arm shaft bolts 13 - 16 ft lbs. exhust manifold bolts 13 - 16 ft lbs. i hope this helps.

Dec 22, 2010 | Nissan Pickup Cars & Trucks

1 Answer

Replacing head


There should be 10 headbolts. This vehicle uses torque to yield headbolts and should be replaced with the new gasket. Bolts 1-8 get torqued to 40 ft lbs initially, bolts 9 and 10 get torqued to 30 ft lbs initially, Then all bolts get turned an additional 90 degrees. I would strongly suggest borrowing a torque angle gauge for doing this or you might be doing the same repair next week.

Feb 12, 2009 | 1999 Chevrolet Malibu

1 Answer

Torque specks


hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right

Feb 12, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...