Question about 2000 Mitsubishi Diamante

1 Answer

The procedure for removing the radio - 2000 Mitsubishi Diamante

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mitsubishi Master
  • 1,207 Answers

You can search the related video about how to remove the radio will be better.

Launch X431

Posted on Jul 17, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the clock display on my 1999 Pontiac Sunfire?


It appears to be that the radio clock display has malfunctioned, and is due for a replacement radio, which could be an aftermarket or oem radio, maybe found at a junk yard.

Tools required for oem replacement radio, torx keys set.

Before working on the radio or other electronics, disconnect the battery cables with 8mm wrench.

Replacing the oem radio is much easier, if you obtain oem radio, compared to aftermarket radio, due to being direct fit.

The radio is same for 1995 to 1999 Pontiac Sunfire and the Chevy Cavalier, regardless of sub models, such as SE,GT, VL,VLX,Z24. etc.

Parts needed for the the aftermarket radio install :Stereo assembly, stereo wiring harness adapter, radio antenna adapter, and dash install kit.wiring diagram for the wire colors / functions, along with tools, such as torx key set, screwdrivers,wire crimper, wire stripper, double ended wiring connectors, hair dryer.

The oem stereo removal video is for the 2000 to 2005 Sunfire / Cavalier, but are the same or very similar procedures.

Link to oem stereo removal procedures.
Pontiac Sunfire Radio Repair and Removal 2000 2005



Link to aftermarket stereo install / connect procedures. ( Sunfire Video )
HOW TO INSTALL AFTERMARKET STEREO PONTIAC SUNFIRE

Link to aftermarket stereo install / connect procedures. ( General Video )
How To Install Car Stereo Single Double DIN Car Audio 101


Have a nice day.


May 12, 2015 | 1999 Pontiac Sunfire

1 Answer

How do you remove the stereo from a Toyota Echo?


NOTE: The following procedure may vary a bit from the system which you have in your car.
TO REMOVE RADIO RECEIVER ASSEMBLY
(a) for Integrated with Panel:
(1) Disconnect the hazard warning signal switch
connector.
(2) Remove the 4 bolts.
(3) Disengage the 4 clips and the 4 claws and
remove the radio receiver.
(4) Disconnect the plug.
(5) Disconnect the 3 radio connectors.
(b) except Integrated with Panel:
(1) Remove the 4 bolts and the radio receiver.
(2) Disconnect the plug.
(3) Disconnect the 2 radio connectors.
1. REMOVE INSTRUMENT PANEL CENTER REGISTER
ASSEMBLY (for Integrated with Panel)
2. REMOVE RADIO BRACKET RH
(a) for Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
(b) except Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
3. REMOVE RADIO BRACKET LH
HINT:
Use the same procedure as for the RH side.

Feb 14, 2014 | 2001 Toyota Echo

1 Answer

How to replace a radio in a 2005 impale


Yes the radio can be removed and replaced.But for that dash has to be removed, then the radio slides out easily by just removing few screws and few wiring connections.Take care you just dont pull the radio forcibly, otherwise wires from other sides gets pulled out.-------- Click this link below and follow the procedure to remove the radio:-- http://technoanswers.blogspot.com/2011/07/how-to-replace-radio-in-2005-chevy.html ---------- This should help.Thanks.Helpmech.

Jul 08, 2011 | Chevrolet Chevy Cars & Trucks

2 Answers

Cd player is not reading cds what can i do to repair it.


Subject: Radio With Six Disc CD Changer Does Not Recognize Loaded CD And Displays An "INITIALIZING" Message, CD Will Not Play, CD Cannot Be Ejected, Or Disc Icon Does Not Illuminate (Reprogram Radio)
Models:
2005-2006 Chevrolet Avalanche, Suburban, Tahoe
2005-2007 Chevrolet Colorado, Express, Silverado Classic, TrailBlazer
2005-2006 GMC Yukon, Yukon XL
2005-2007 GMC Canyon, Envoy, Savana, Sierra Classic
2005-2006 HUMMER H2 with Six Disc CD Changer Equipped Audio System (RPO UC6)
Condition
Some customers may comment on any of the following conditions:
• The CD loaded in the radio will not play.
• The CD loaded in the radio will not eject.
• The disc icon on the radio will not illuminate.
• The radio displays an "INITIALIZING" message for approximately 30 seconds after vehicle start up.
Important: Do not attempt to play CDs with paper labels on them in this CD player. The labels may warp or wrinkle and jam the CD player mechanism. Refer to the Compact Disc Care and Cleaning procedure (Document ID# 1656123) in SI for more information.
Technicians are to reprogram the radio with new operating software using the following procedure:
1. If the radio has a CD(s)2008 General will be necessary to reset the radio and remove them
before the radio is reprogrammed. Remove and reinstall the radio fuse to reset the radio and then eject the CD(s). If cycling the power to the radio does not allow the CD(s) to be removed, the radio may have another failure that will not be corrected by the reprogramming procedure that follows. Refer to the Diagnostic Starting Point - Entertainment procedure in SI to begin your diagnosis of this failure to eject CDs concern before reprogramming the radio.
2. Reprogram the radio using the Service Programming System (SPS) with the latest software available on TIS2WEB. Refer to the SPS procedures and the Radio Programming and Set procedure in SI for more information. As always make sure your Tech 2® is updated with the latest software version.
3. Verify proper operation of the radio and make sure that all CDs can be ejected.

Hope helps (remember to rate this).

Oct 03, 2010 | 2005 Chevrolet Trailblazer Ext

1 Answer

REMOVAL OF THE RADIO


Here ya go!

4c47b30.gif
Exploded view of the radio, tape player or CD player removal, 1990-94 vehicles

  1. Disconnect the negative battery cable. Wait at least 60 seconds before beginning the remainder of the procedure, in order to disarm the Supplemental Restraint System (SRS).
  2. Using a plastic trim tool, remove the radio panel. Pry the lower part of the radio panel away first, then separate and remove the panel.
9d61d07.gif
Using a plastic trim tool, carefully pry the radio trim panel away

08e17de.gif
Remove the center trim panel for access to the radio retainers

WARNING When removing and installing the floor console, do NOT allow it to bump against the SRS-ECU!

  1. For 1995-98 vehicles, remove the floor console assembly, as outlined in Section 10 of this manual.
  1. Remove the mounting bolts and pull the radio receiver, tape player or CD player out slightly. Detach all harness connectors and remove the unit from the vehicle.
4c48f2d.gif
After removing the console, unfasten the radio mounting screws

e7143a0.gif
Pull the radio out enough to access the connectors

4cb0996.gif
Unplug the electrical connector from the rear of the radio ...

3795675.gif
... then disconnect the antenna lead and remove the radio from the vehicle


Installation is the reverse of the removal procedure.

Oct 29, 2009 | 1992 Eagle Talon

1 Answer

How to take dash apart to get to the radio


The moulding around the radio removes quite easily. Remove the ashtray, 2 screws. Remove the slideout cupholder. 2 screws. The moulding around the radio pulls straight out. It has slideout or popout clips. Once that is removed, unscrew the 2 10 mm or philips screws that hold the radio in. Slide out the radio, another 10 mm ground screw on back, then unplug the antenna, 2 electrical connectors and that's it. I dont recommend an aftermarket radio without a schematic or someone that knows what they're doing. Like in the chiltons books, "reverse disassembly procedure to reassemble". Hope this helps

Oct 09, 2009 | 1995 Dodge Caravan

1 Answer

Fixing heater core on Mercury Villager front one


go here for lots of help

http://groups.yahoo.com/group/villagerquest/

Heater Case Removal
  1. Drain the engine coolant. Refer to Section 03-03 for the procedure.
  2. Disconnect the battery ground cable (14301).
  3. Disconnect the heater water hoses (18472) from the heater core (18476) at the bulkhead.
  4. Remove the instrument panel lower center panel (04494). Refer to Section 01-12 for the removal procedure.
  5. Remove the glove compartment and LH instrument panel lower cover (044L97). Refer to Section 01-12 for the removal procedure.
  6. Remove the instrument panel ash receptacle (04810).
  7. Remove the two upper center instrument panel finish panel screws and the two lower center instrument panel finish panel screws.




  8. Remove the center instrument panel finish panel (044D70) and disconnect the cigar lighter socket and cigar lighter illumination lamp electrical connectors.
  9. Remove the four radio chassis bracket screws and pull the radio chassis (18806) and climate control assembly from the instrument panel (04320). Disconnect the radio chassis electrical connectors, the antenna lead, the three climate control electrical connectors and remove the radio chassis and climate control assembly.
  10. Remove the two heater outlet floor duct screws. Remove the heater outlet floor duct (18C433).




  11. Remove the four RH instrument panel lower reinforcement bolts and the RH instrument panel lower reinforcement (045F08), then the four LH instrument panel lower reinforcement and the LH instrument panel lower reinforcement.
  12. Remove the anti-lock brake control module (2B373). Refer to Section 06-09 for the removal procedure.
  13. If equipped, remove the speed control amplifier. Refer to Section 10-03 for the removal procedure.
  14. Remove the electronic door lock control processor (14B001). Refer to Section 01-14A for the removal procedure.
  15. Remove the passive restraint control module. Refer to Section 01-20B for the removal procedure.
  16. Remove the two center duct screws and remove the center duct (19D633).




  17. Remove the two ground wire bolts.
  18. Remove the three U-bracket-to-chassis nuts.




  19. Remove the four U-bracket bolts and remove the U-bracket.


  20. Remove the two RH and the two LH instrument panel bracket bolts and remove the instrument panel brackets (042C74).
  21. Remove the RH inner duct.
  22. Remove the LH inner duct.
  23. Remove the two accelerator pedal and shaft bolts and then the accelerator pedal and shaft (9725).
  24. Remove the accelerator pedal stop screw and then the accelerator pedal stop (9816).
  25. Remove the heater outlet duct screw and remove the heater outlet duct.
  26. Remove the temperature blend/panel bypass door actuator motor. Refer to the procedure in this section.
  27. Remove the panel/floor/defrost door actuator motor. Refer to the procedure in this section.
  28. Remove the three A/C evaporator register duct screws and remove the A/C evaporator register duct.
  29. NOTE: The A/C evaporator/blower motor assembly does not have to be removed in order to remove the heater assembly.

    Remove the four A/C evaporator/blower motor assembly screws to aid in the removal of the heater assembly.
  30. Remove the four heater assembly screws.
  31. Remove the heater assembly.

Sep 30, 2009 | 1996 Mercury Villager

2 Answers

How to remove the care stereo


Carefully remove the trim plate around radio, (clips into dash)
Remove screws and pull out radio
Disconnect radio connectors on rear of unit and antenna cable
Reverse procedure to install...

Mar 26, 2009 | 2001 Daewoo Lanos

3 Answers

1999-2003 Ford Windstar radio removal procedure


remove the trim around the radio face be careful not to break it, it should snap off its a delicate proceedure take radio face plate off ( if equipped) radio should come out

Nov 09, 2008 | 2003 Ford Windstar

2 Answers

Radio Cover won't stay closed


Hi

To access the radio cover mechanism you have to remove the central trim around the radio, you may have to remove the radio as well whoch is a pain if you do not have the Audio tools.

The cover is a simple device and is easy to remove and check. You will see 2 very small clips that you can press with a flat head screwdriver and the whole unit pops out easily.

If you have problems email me and I will scan and send you the procedure, I bought the bentley manual and is amazing!!

Aug 05, 2008 | 2001 Audi TT

Not finding what you are looking for?
2000 Mitsubishi Diamante Logo

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...