Question about Cars & Trucks

Open Question

Toyota townace manual

Replace headlight bulb

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
LEFTY64
  • 69 Answers

SOURCE: I need to replace the headlight on my 1994 Toyota Pickup

CAUTION Most headlight retaining rings and trim bezels have very sharp edges. Wear gloves. Never pry or push on a headlamp; it can shatter suddenly.

  1. Make sure the headlight switch is in the off position.
  2. Loosen the parking and side turn signal unit retaining screws. Then remove the units unplugging the connectors.



0900c15280061083.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: After removing the parking lamp screws, push on the grille clips to release the grille from the truck
  1. Next, open the hood to gain access to the grille clips. Using a flat-bladded tool, push on the clips to release them and the grille.



0900c15280061084.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Remove the grille from the truck and set aside
  1. The sealed beam is held in place by a retainer and either 2 or 4 small screws. Identify these screws before applying any tools.DO NOT confuse the small retaining screws with the larger aiming screws. There will be two aiming screws or adjustors for each lamp. (One adjustor controls the up/down motion and the other controls the left/right motion.) Identify the adjustors and avoid them during removal. If they are not disturbed, the new headlamp will be in identical aim to the old one.



0900c15280061085.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Remove the headlight bezel which is secured by screws
  1. Using a small screwdriver (preferably magnetic) and a pair of taper-nose pliers if necessary, remove the small screws in the headlamp retainer. DON'T drop the screws; they vanish into unknown locations.



0900c15280061086.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Be careful when removing the headlight bezels, they can be sharp
A good kitchen or household magnet placed on the shank of the screwdriver will provide enough grip to hold the screw during removal.
  1. Remove the retainer and the headlamp may be gently pulled free from its mounts. Detach the connector from the back of the sealed beam unit and remove the unit from the car.



0900c15280061087.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Pull the light out, then unplug the wiring harness from behind it

Posted on Apr 07, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: how to change a headlight light bulb on toyota prius 2006?

they are usually changed from inside the engine compartment. you should be able to gain access to the bulb behind each headlight bazel. the socket often has to be turned to remove it. be careful not to touch the new bulb with your fingers as that will shorten it's lifespan. you may have to remove the battery if the burnt out bulb is on that side.

Robert

Please take a moment to rate this solution... thanks

Posted on Apr 15, 2009

  • 157 Answers

SOURCE: How do you replace the headlight bulb on a Toyota Corolla 2003

You can and it is not difficult, there are two bolts holding the top of the headlight to the body just over the radiator and a couple of screws holding the indicato in place, but you can access the back of the light fitting without doing so . It is a bit of a squeeze on the battery side.

Posted on Mar 08, 2010

  • 1 Answer

SOURCE: headlight bulb toyota celica 92 model

h4 the 3 pin halogen ones

Posted on Apr 14, 2010

  • 1 Answer

SOURCE: Toyota Sienna 2004 Headlight Problem

If you have the HID bulbs, and there is moisture in the bottom of the assembly, the high voltage box at the bottom will not work. this requires removing the whole headlamp, removing the circuit board from the bottom and drying out. I have done mine twice before finally finding how water was getting in at the top seam of the lamp assembly. You will have to dis-assemble part of the wheel well and bumper cover to gain access to all the mounting bolts. Best of luck

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i download townace owner manual


toyota

amazing huh? but you never said year.
http://www.toyota.com/owners/web/pages/resources/owners-manuals#Owners-Manuals

USA manuals. if not usa say so........

Feb 11, 2014 | Toyota Cars & Trucks

4 Answers

Headlight changing


please use chelton manual for getting instructions with diagrams.

remove the side screws and then remove the rim of the light

now you can access the lights


Oct 17, 2008 | 1992 Toyota Celica

1 Answer

Toyota townace mecanical manual


Check with dealership for manual.

Sep 12, 2013 | Cars & Trucks

1 Answer

Toyota townace service manual


How many litters of Ingine oil of Toyota townace

Mar 15, 2012 | Toyota Cars & Trucks

3 Answers

Daytime Running Lights Inoperative 2002 Toyota Camry


[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."


2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]


My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

Dec 30, 2011 | 2002 Toyota Camry

1 Answer

How to replace toyota matrix front headlight bulb


Hi,

Replacing a headlight on a Toyota Matrix is a simple process that only requires the use of a screwdriver and a replacement bulb. The Matrix uses 9006 bulbs for the low beams and 9005 bulbs for the high beams. Headlight bulbs can be purchased at auto parts stores.
Replacing Low Beam Bulb
  1. Turn off the engine of the Matrix and open the hood
  2. Rotate the bulb base in the headlamp assembly counterclockwise to remove the low beam bulb. Unplug the electrical connector. If the connector is too tight, wiggle it slightly to help remove it.
  3. Install a new bulb into the connector and place it into the assembly. Rotate it clockwise to lock it into place. Close the hood.
Replacing High Beam Bulb
  1. Turn off the engine of the Matrix and open the hood. If replacing the left-hand headlight, remove the air cleaner duct by removing the securing clip with a screwdriver and pulling the duct out of the vehicle.
  2. Turn the bulb base counterclockwise to remove it. Unplug the electrical connector.
  3. Install a new bulb into the connector and place the bulb into the assembly. Rotate it clockwise to lock it into place. Reattach the air cleaner duct if replacing the left-hand headlight. Close the hood
I hope this helps.

Best regards.

Oct 29, 2010 | 2005 Toyota Matrix

2 Answers

Have flashing light on toyota townace not sure why


Try this website for resolving car problems by downloading a FREE service manual for your vehicle. This is not an owners manual but a factory mechcanic's manual.

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 01, 2010 | 1994 Toyota Pickup

1 Answer

Where do you refill the oil in a Toyota Townace


Dipstick, oil filler , filter etc are under the passengers front seat.
If you lift the carpet immediately in front of the seat, you will see a pair of clips holding down the seat, unlatch them and lift the seat ( in some models they hide a clip in the centre console).
The brake fluid is under a cover in the dash.

Mar 27, 2010 | 1985 Toyota Passenger

1 Answer

HOW TO REPLACE A HEADLIGHT BULB ON A TOYOTA PREVIA 2.0D T3


Replacing a headlight bulb for Toyota Previa. Quite simple. Open the hood. Look for the black plastic coupling or ring on the backside of the headlight. Grasp and turn counterclockwise (i believe it will be about a quarter turn). pull the socket out, then replace the bulb. I believe it is code #9004. Strongly recommend replacing both headlights at the same time.


Good luck

Oct 08, 2009 | Toyota Previa Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...