Question about Nissan Stanza

1 Answer

1985 nissan stanza

Car doesn't go into first gear all the way. It will go in half way and then pops out.

Posted by on

Ad

1 Answer

Standard Transmission ?
Clutch or Trans Problem
If you can get into any gear but first,then internal
trans issue & it has to come out & apart

Posted on Jul 17, 2013

  • Michelle Thompson Jul 17, 2013

    It is a manual transmission, which I don't believe is standard.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: Directions replace front wheel bearings on a 1985 nissan stanza?

996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Posted on Jun 23, 2009

countrysi248
  • 443 Answers

SOURCE: l986 Nissan Stanza starter

disconnect the battery and check out starter wires you have to make repairs to the wires near the starter .. but do it with the battery disconnected .. thanks Jerry holler if you need more

Posted on Jan 29, 2009

messstat
  • 365 Answers

SOURCE: Need info on replacing the front wheel bearings on

WOW...85? Go to AutoZone or Napa and order a Chiltons manual ($25)...
Good Luck getting parts

Posted on Jun 23, 2009

  • 1 Answer

SOURCE: temp gauge reads half but there is no heat blowing

How do you remove the door panel on 1990 nissan stanza xe I'm trying to swap out the 5x7 passenger side speaker. will a 6x8 speaker fit? I'm trying to remove bottom part ONLY of door panel? Also, where is the wiper washer reservoir located on the 90 Stanza? I cant find that of the temp gauge sensor on the engine. I have no reading on the instrument panel temp gauge so figure it's the sensor. Am I correct on this? Ideas? I've looked everywhere on the net for a righr rear tail light lens to no avail. Yikes! *lol*

Posted on Mar 21, 2010

SOURCE: I have a 1987 Nissan Stanza, standard

Sounds like the piece of wood loosened / bent / damaged the transmission linkage. Needs inspecting / repairing. More info, let me know.

Charlie

Posted on Feb 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace cv joints on a 1985 nissan stanza


It's better to buy a manual. find them at you local auto part store. There isn't enough space in here to explain. I've replaced stanza cv before, just be careful, For your safety use jack stands.

Feb 12, 2016 | 1985 Nissan Stanza

1 Answer

In my 1995 Nissan 200sx ser it doesn't wanna go in


Not sure about popping out of reverse. But 5th gear pop out is a problem on these, nissan never had a recall, but they offer a slightly altered version of the 5th gear that is available. Go read up at nissanforums there's a lot there, pics and all, even a petition to Nissan for everyone who's had the same problem, me included.

May 03, 2012 | 1995 Nissan 200SX

1 Answer

Need info on replacing the front wheel bearings on my front wheel drive 1985 Nissan Stanza?


WOW...85? Go to AutoZone or Napa and order a Chiltons manual ($25)...
Good Luck getting parts

Jun 23, 2009 | 1985 Nissan Stanza

1 Answer

Nissan Stanza 1986 car bucks and cuts out when accelerating


I would check the vacuum advance. or maybe an O2 sensor

Feb 19, 2009 | 1985 Nissan Stanza

1 Answer

L986 Nissan Stanza starter


disconnect the battery and check out starter wires you have to make repairs to the wires near the starter .. but do it with the battery disconnected .. thanks Jerry holler if you need more

Jan 29, 2009 | 1986 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...