Question about Cars & Trucks

Open Question

How to set timing on opel corsa 1.6 8v

There is no plastic covers,i need to know how to set crank an cam pulley marks for timing

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

Ad
  • 7 Answers

SOURCE: Opel Corsa timing belt replacement

Need to know the engine code..

Posted on Jan 13, 2010

alicantecoli
  • 22219 Answers

SOURCE: How to set pump, crank and cam timing on opel corsa 1.7d utility, model 2003

Not sure here as to the type as some have a bolt in the block in line with the crank and special tool is used to locate TDC ,If the timing belt broke then you have bent valves anyway so the head will have to come off .If you reply with more details then i will advise how to do it with no timing marks also is this a common rail with just a high pressure pump or is it a intermediate with injector pump but the injectors having electronic sensor on one of the injectors if that makes sense to you

Posted on Oct 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt diagram daewoo nubira 1998


Here are the written instructions, i do not have the pictures, it is a very good set of instructions and clearly written.

Required tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers

If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.

Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

Nov 15, 2011 | 1999 Daewoo Nubira

1 Answer

Engine Timing marks on a 4.0 ford ranger on a 2005


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Nov 02, 2011 | 2005 Ford Ranger

1 Answer

Where us my 1996 chevy v6 C1500 pickup timing chain located. I need the area and schematics; as i dont know where to start /


the timing chain on the 4.3 is on the front of the engine. you will need to remove the water pump and the crank pulley to access the timing chain cover. You can see the cover if you look behind and above the crank pulley. the cover will be held on by about 15-20 bolts.

make sure you line up the timing mark on the cam gear with the timing mark on the crank gear. there will be a dot on each. when the are lined up the dot on the crank pulley will be at 12 oclock and the dot on the cam gear will be at six oclock.

you will need a puller to remove the crank pulley and the crank gear. Other than that its just nuts and bolts.

Jun 27, 2011 | 1996 Chevrolet C1500

1 Answer

How do you put a timing belt on a 2002 daewoo leganza 2.2 liter engine twin cam and what are the marks?


Here are the full instructions and tools needed.

Required tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers

If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.

Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

Jan 07, 2011 | 2002 Daewoo Leganza

1 Answer

I dont know how to set the timing for my 2000 nubria daewoo


You will need these tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers.

If you are doing this because your timing belt broke, you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley (the four Allen head bolts only not the 17mm bolt in the center.) Remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover, three clips on top and two 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center (TDC) on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover (notch in cover with notch in pulley) on the camshaft pulleys (intake cam line up the line on the pulley with the line on the inner cover) (exhaust cam line up the arrow on the pulley with the arrow on the inner cover) Now loosen the 13mm bolt in the belt tensioner and using the Allen wrench, rotate the tab until there is slack in the belt. Remove the timing belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the exhaust cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed, rotate the crankshaft over two revolutions and make sure is rotates freely, and your timing marks are aligned perfectly. If not, the engine will not run properly, tension the belt as needed. Installation is the same as removal. To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple. In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long. One more item that you might as well replace while you are in there is the cam position sensor if you have not already replaced it as there have been issues with them, and the timing housing has to be opened to get to it. The timing is set at: 8 degrees (both manual and automatic transmission)

Oct 23, 2010 | 2000 Daewoo Nubira

1 Answer

Need to know the markings to set the time on a daewoo lanos


Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Jun 08, 2010 | 2001 Daewoo Lanos

2 Answers

Replaced water pump and now i need to know how to reset timing


I hop you are replacing the belt and tensioner/ idler pulleys. the crank pulley has a notch approx 12'oclock. the cams will be marked rear cam "I" and front cam "E" .. put both letters at 12 o clock. there should be a notch at the top of the cover for the cams at 12 o clock. thats all there is to it. to tension the belt, after you have it all timed up. put some tension on it, tighten tensioner bolt, turn the engine 2 revolutions, then double check your marks, push down with you thumb between the cam sprokets with 20 lbs of force, the belt should delfect about 10MM if its too loose, loosen the tensione rbolt an dturn it tighter a little more an dck tension again. If you get it too tight it will whine and wear the cam journals, too loose and timing will not be correct.

Sep 18, 2009 | 2001 Kia Sephia

1 Answer

Leaky front crank seal i just need to know what needs to be taken off to get to it and what i should be able to get arround


This requires cam belt(s) removal in order to access the seal behind the crank pulley/balancer. The front of engine comes apart including all belts, covers,pulleys and gears.Do fully understand there is special cam timing marks when setting back up ....look for three small dashes 30 degrees or so from tdc (zero) timing marks on the back flywheel

Sep 17, 2009 | 1999 Subaru Legacy

2 Answers

Iam changing the timing belt need to know the marks to set it on on a 1990 ford mustang 4cyl


If you mark your timing gears, crankshaft & camshaft against the cyl. head & block with white paint before removing the old belt you really can't go wrong. After fitting the new belt rotate the engine by hand and re check your marks.

Aug 12, 2009 | 1990 Ford Mustang

4 Answers

Timing marks on volvo s40


the crank has the only mark you have a procedure for the cam gear you should see if the local dealer will print this out for you

Jul 01, 2008 | 2004 Volvo S40

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...