Question about 2005 Toyota 4 Runner

Open Question

2005 toyota 4 runner door panel removal

Keyless entry nor key will open drivers door

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bad_dog1
  • 104 Answers

SOURCE: drivers door power lock wont work.

Either the wring going to that motor or the motor itself is bad.

Posted on Mar 09, 2009

Ad
  • 36 Answers

SOURCE: Toyota 4runner gate window, wiper, and keyless entry not working

make sure the back window is all the way up then try the wiper, if it still does not work then it is a sensor for the rear window (about $30.00) if you installed it yourself

Posted on Jul 21, 2009

  • 1986 Answers

SOURCE: Driver side keyless entry does not work. Other

does the door unlock with a key? if not, then you may have a disconnected linkage. You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Way cheaper to do it yourself than have the dealer do it... cost me $30-50 to do it myself and the dealer was gonna charge me $300

Posted on Aug 14, 2009

Testimonial: "Yes, driver's door opens with key........ so the linkage might still be in place......then what?"

  • 347 Answers

SOURCE: Remove a driver side door panel on a 2000 Toyota Limited 4 Runner

remove the screws that hold the inside door handle and clips behind the door panel

Posted on Sep 20, 2009

  • 160 Answers

SOURCE: I have a 1993 Toyota 4 runner and I can't unlock

need to pressure test system possibly minor problem such as heater hose split please rate

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless entry


If you can open this door using a key - the problem is in the locking motor. Take off the door panel and give power to loking motor directly from the 12 V battery.

Jul 12, 2014 | 2010 Toyota FJ Cruiser

1 Answer

2004 Suzuki Gran Vitara Keyless entry


Try this

2004 XL7

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.

8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s)

Jun 01, 2014 | 2007 Suzuki XL-7

2 Answers

Bttery is dead, can't get in, have keyless entry, no key, can't open the hood or anything, toyota venza


remove grille and move latch to open hood-boost battery and use key fob to enter or have locksmith or service station use a slim jim or other type of device to unlock door

May 13, 2012 | 2009 Toyota Venza

1 Answer

I have a 2003 Toyota 4-Runner. The keyless alarm has stopped working on the drivers side door.


On the driver side the actuator is more likely the culprit,the linkage could of come off or the actuator just doesnt work

Mar 06, 2012 | 2003 Toyota 4Runner

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless entry 2005 grand am i put new ignition on car, 2005 grand am it came 2005 grand am that i own that was wrecked my car that i want to put it on did have remotes when i bought it they were lost, igot...


To program the transmitters, perform the following procedure while seated in the vehicle driver's seat:

Close all the vehicle doors.
Remove the ignition key from the ignition lock cylinder.
Press and hold unlock on the door lock switch.
Important: To successfully enter the keyless entry programming/diagnostic mode, steps 4 through 6 must be completed within 25 seconds of pressing the door unlock switch.

While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
Release the door lock switch. The chime will sound three chimes to signal that transmitter programming/diagnostic mode is active.
Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for approximately 4 seconds. The chime will sound two times to signal that the transmitter has been programmed successfully.
To exit the transmitter programming/diagnostic mode perform either of the following:
• Turn the ignition switch to the RUN position.

• Remove the ignition key from the ignition switch

Oct 21, 2009 | 2005 Pontiac Grand Am

1 Answer

Driver side keyless entry does not work. Other


does the door unlock with a key? if not, then you may have a disconnected linkage. You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Way cheaper to do it yourself than have the dealer do it... cost me $30-50 to do it myself and the dealer was gonna charge me $300

Aug 14, 2009 | 2002 Toyota RAV4

1 Answer

Remove a driver side door panel on a 2000 Toyota Limited 4 Runner


remove the screws that hold the inside door handle and clips behind the door panel

Jun 14, 2009 | 2000 Toyota Corolla

1 Answer

Program my remote


Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.

Jan 13, 2009 | 2001 Toyota Tacoma

Not finding what you are looking for?
2005 Toyota 4 Runner Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...