Question about Cars & Trucks

Open Question

On the master cylinder, which line goes to the to the front brakes

On a 1996 chevy tahoe 5.7 on the master cylinder which hole go to the front brake line

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: back brake lines wont bleed on 77 chevy truck

Check out this link & read about combination valve & how to center it when bleeding.

http://www.autozone.com/addVehicleId,1321403/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528007a632

Posted on Jan 23, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: 1996 PLYMOUTH VOYAGER SOFT BRAKE PEDAL AIR IN LINES

I am a hydraulic technician and I can tell you that air is a killer in the hydraulic system.

Start from the rear and work your way forward. I f you are using the two person method, make sure the second person keeps the master cylinder full. If the fluid level dropped anywhere in between pressing and releasing the brakes....you have a lot of air in the system.

Make sure you are tightening the bleed valve when the brake pedal is full pressed.

Remeber...start from the rear brakes first, then do the front.

Posted on Mar 16, 2009

  • 1779 Answers

SOURCE: 1998 chevy s10- brake pedal goes to the floor-

Did you put fresh fluid in the master cylinder? I really think you still have air in the lines. To bleed manually, start with the bleeder the greatest distance from the master cylinder, car running, helper pushing down about half way on brake pedal and releasing 3 times, on 3rd time, holding pedal down to half way depressed point while you open the bleeder valve. Repeat until you are sure all air has been flushed out. Check master cyl reservoir level often, because if it gets low and you **** air into the system, you have to start all over again. Go to wheel next greatest distance from master cyl, repeat above, working your way to wheel closest to master cyl last.

Posted on Apr 12, 2009

yotaguy
  • 232 Answers

SOURCE: brake light stays on after replacing brake line and bleeding

You may need to do a code scan,this will reset the computer and reset any codes if the brake problem has been taken care of.Autozone Shucks/Kragen/O'Reilly's will do this for free.

Posted on May 31, 2009

  • 158 Answers

SOURCE: 00 Chevy EHCU HELP

bleed each separately

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Ford Explore No brake paddle when truck is runny paddle goes to floor


Master cylinder brake booster bad wheel cylinders hole in a brake line

Mar 10, 2014 | 1996 Ford Explorer

1 Answer

2002 chevy tahoe no front brakes only rear brakes


IT appears that only half of the master cylinder has bled properly. Try loosing the pipe nuts at the m/cyl and gently pump the pedal until you get fluid out of both lines. Then re-bleed the system starting at the longest line first ending at the shortest. Some master cylinders have a plunger fitted in the middle of the cylinder and this is there to still have brakes if a line fails. It may be necessary to remove it an plug the hole temporarily while you bleed the system as to stops one piston in the cylinder from moving and allowing proper bleeding

Jul 17, 2013 | 2002 Chevrolet Tahoe

1 Answer

Brake petal goes to the floor, Feeling very loose!


Find out what the issue is between the discs and pads and master cylinder. Take it to a garage and don't drive until safe!

Apr 04, 2017 | 1996 Chevrolet Tahoe

1 Answer

Brake issues on 1996 Chevy Blazer


You should check your vacuum lines make sure they are all connected plus the line you keep disconnecting is collasping onto its self which in turn will make the brakes stick so you must have one of the ends plugged.

Jul 25, 2012 | 1996 Chevrolet Blazer

2 Answers

I have a 1996 GMC c2500. It had both rear wheel cyl. leaking and I replaced them. When I tried to bleed them I have no fluid to the rear. I checked at the master cyl and I do have flow there,but there is...


I take it you are trying to bleed the rear brakes and are not getting any fluid. When you are not getting any fluid to the rear only. It can only be two things. The per portioning valve. This is what supplies the brakes on the rear with only 10% breaking.

Oct 05, 2010 | 1996 GMC Jimmy

1 Answer

Need to replace a brake booster on a 1998 chevy cavalier


get ready for some work.you need to remove the master cylinder nuts that hold master cylinder to brake booster.once you remove nuts you have 2 choices remove master cylinder to remove booster. to keep from bending brake lines.or you can leave master cylinder in pull it toward you easily careful dont bend lines .disconnect vacuum line at booster .go inside vechicle to floor on driver side loosen four nuts on floor to booster .disconnect power brake push rod from brake pedal .dont force pushrod to the sides when disconnecting it.remove four booster nuts then remove booster.when in stalling the new booster loosely install four nuts then connect the push rod to the brake pedal .install new clip tighten the booster unit .if you decide to remove master cylinder use inline wrenches on master cylinder to remove lines.also plug the master cylinder brake line holes to keep from losing all brake fluid.

Apr 26, 2009 | 1998 Chevrolet Cavalier

1 Answer

Unable to bleed front brakes


loosen the front brake line that goes to the master cylinder fill master cylinder up with fluid and bleed it first by attaching a flexible line from master cylinder front brake side submerge that line into jar of brakefluid keeping air from entering line get someone to pump brake pedal while ur holding line in a jar keep refilling the brake resivoir so no air gets in, once the master is bled front brake side then reattach the origional brake line then remove bleed screw from caliper and let fluid gravity flow down to calliper then bleed the normal way. more than likely your master cylinder has air trapped in the front portion good luck

Jul 01, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...