Question about Cars & Trucks

1 Answer

I cannot get air to flow out of the center vents in my 2005 ford focus zx4

Posted by on

1 Answer

Duct Vent Motor under dash (Cabin Air Flow Vent)
not defrost,floor,recirculate or blend door,ones
Hope you can reach it
If you go to Motorcraft Web Site you can see a diagram
of the vent motor or actuator & order on Amazon,BUT
you have to first diagnose that is the issue & get the right
motor if it is.
I use a professional scan tool to check for codes on the
electric ones & then look under the dash to see if they move
as they should
Near impossible to get your hands up there to replace

Posted on Jul 17, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 691 Answers

SOURCE: broken rear wheel stud on a 2005 ford focus zx4 se

  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Posted on Sep 25, 2009

BCAS1298
  • 3092 Answers

SOURCE: I need serpentine belt diagram for 2005 ford focus

IF YOU GO TO ANY AUTO PARTS THEY WILL BE MORE THEM GLAD TO GIVE YOU THAT INFO. AUTO ZONE WILL DO THAT FOR YOU.

Posted on Nov 04, 2009

SOURCE: how do i clear fault codes in my srs module

with a scanner, no way to do it without the proper tools

Posted on Nov 27, 2009

  • 1168 Answers

SOURCE: what type of antifreeze is used with a 2005 Ford Focus

Hello mk12x.

Ford specification is Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A (green color) with a mix of 50-50 coolant and clean water.
I hope your repair goes well for you.

Kl

Posted on Dec 17, 2009

2coolrick
  • 560 Answers

SOURCE: diagram on how to install ford focus 2006 zx4 serpentine belt?

Autozone or a similar parts retailer will print one for you for free.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a dash on a 2005 ford focus zx4?


there is going to be a whole lot of screws, take a few pitchers as you go unless you can remember everything from start to finish take the battery connections off then you can get going, take the glove box out,kick panels off drop the steering column down but don't pull it out just unbolt it remove the center console, just pay Attention to how you take the dash apart.

Dec 15, 2016 | 2005 Ford Focus ZX4

1 Answer

I got a zx4 2005 ford focus that will not engage when I put it in to gear. What can I do?


broken cable. try operating the gearshift while looking for the operation on the transmission itself. raise hood and observe the transmission.

Apr 16, 2015 | 2005 Ford Focus ZX4

1 Answer

Air condition


What does "evaporator is working" mean ?
Are the compressor and radiator fan running ?
Is the system full of freon ?

Jul 20, 2013 | 2005 Ford Focus ZX4

1 Answer

Heater/ac vent blower switch stuck in 1 position


this is usually controlled by vacum look for a broken or leeking vacum line

Feb 12, 2013 | 2005 Ford Focus ZX4

1 Answer

Diagram for heater control box for ford focus 2005 zx4 se


what do you need ? the one going to the blower motor or blower resister or the blend door motor

Jan 06, 2013 | Ford Focus Cars & Trucks

1 Answer

Whre are airbag sensors located on 2005 ford focus zx4-se


in the front of the car , look for a connector that has a blue and orange connector,, follow those wires to the sensor,, if you google Focus air bag problems, you will see that Ford has lots of problems concerning this make, and might be under recall

Jul 31, 2011 | Ford Focus Cars & Trucks

1 Answer

How can i add freon to my cars' air conditioner for a ford focus zx4 se?


Charging the System

  1. Lubricate the refrigerant system with the correct amount of clean PAG oil.
  2. Connect an R-134a A/C service center to the low-side and high-side service gauge port valves following the operating instructions provided by the equipment manufacturer.
  3. Set the refrigerant charge amount, and charge the refrigerant system following the instructions provided by the equipment manufacturer.

May 23, 2010 | 2005 Ford Focus

1 Answer

Where is my iat sensor on a 2005 ford focus zx4 2.0 duratech engine


IAT sensor stands for Idle Air Temperature

Try this website to download a free manual

Trouble trees are listed for all makes in the manuals for dianogstics



http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 01, 2010 | 2005 Ford Focus

1 Answer

What type of antifreeze is used with a 2005 Ford Focus


Hello mk12x.

Ford specification is Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A (green color) with a mix of 50-50 coolant and clean water.
I hope your repair goes well for you.

Kl

Dec 17, 2009 | 2005 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...