Question about 2000 Nissan Xterra

1 Answer

Sensor crankshaft I need changed sensor crankshaft

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Http://www.youtube.com/watch?v=NXxKTBynjzc

This is a 2005, but it should be very similar.

Posted on Jul 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1336 gm code


P1335 CHEVROLET P1335 CHEVROLET - Crankshaft Position Circuit Possible causes
- Faulty Crankshaft Position Sensor
- Crankshaft Position (CKP) Sensor harness is open or shorted
- Crankshaft Position (CKP) Sensor circuit poor electrical connection help.png Help with this
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
P1335 CHEVROLET Description
The Crankshaft Position (CKP) sensor sends pulses to the Powertrain Control Module (PCM) as the reluctor wheel teeth rotate past the CKP sensor. The PCM uses the CKP pulses to synchronize the ignition and fuel injector operation, and to time the interval between each CKP pulse. The PCM determines when an excessive change in crankshaft speed occurs by comparing each new time interval with the previous interval. A misfire causes an unexpected change in the crankshaft speed. A certain amount of acceleration/deceleration is expected between each firing stroke, but if the crankshaft speed changes more than an expected amount, the PCM interprets this as a misfire. The interval between CKP sensor pulses is extremely small. At high engine speeds, slight variations in the following components make misfire detection difficult:
- Crankshaft
- Reluctor wheel
- CKP sensor
The PCM learns variations during the Crankshaft Position System Variation Learning Procedure. The PCM compensates for these variations when performing detect misfire calculations. Only a scan tool can command the PCM to perform the Crankshaft Position System Variation Learning Procedure again.
Perform the learning procedure after the following actions:
- A PCM replacement
- Any operation or repair involving the crankshaft, the CKP sensor, or the CKP sensor to reluctor wheel gap relationship.
- An engine replacement.
- The ignition switch is in the ON position until the battery is drained.


Read more: http://nissanhelp.com/diy/obd_codes/p1335_chevrolet.html#ixzz37IoD1Imx

Jul 12, 2014 | 2001 GMC Safari

1 Answer

GM OBD2 code 1345 causes


either the crankshaft sensor needs to be changed or camshaft sensor.Both work together and are under that code.If you change the sensors you will need a crankshaft profile correction.This should be done by your dealer with the proper scan tool.

May 01, 2012 | 1999 Chevrolet K1500

1 Answer

Where is the crankshaft sensor located on a 2004 kia optima


I just replaced the crankshaft sensor back in November. It is a bit of work to access, but you will find it on the inner crankshaft sprocket. This is under the lower timing belt cover. It is just a black sensor that partially covers the sprocket. You will need to remove the serpentine belts and outer crankshaft sprocket to access it. At the time I needed to change it, I also happened to be changing the timing belts as well so if you need those done soon, this would be a good time to get them done.

Feb 14, 2011 | 2004 Kia Optima

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

No fire to coil from coil on 96 model Jeep Grand Cherokee.


You need to put the harmonic balance for the 96 jeep on this motor,then put the crankshaft sensor on for the 96 jeep on the vehicle,this should fix you up.The crankshaft sensor and the harmonic balance have to go together.If I can be further help,let me know.>>roniecon@gmail.com

Aug 18, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

1 Answer

Need to change crankshaft position sensor for 2001 elantra


down by your crank shaft pulley you will find a sensor with 2 wires ruining into it and 1 bolt holding the sensor in remove the bolt and twist and pull on the sensor then slide the new sensor in then reinstall bolt and wire

Mar 08, 2009 | 2001 Hyundai Elantra

2 Answers

Crankshaft Location


I was told that there is a crankshaft sensor on the vehicle and I am trying to find out where it is located.

Oct 04, 2008 | 2004 Chrysler Pacifica

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...