Question about Cars & Trucks

Open Question

Does my 2002 nissan altima have a non interference engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

BCAS1298
  • 3092 Answers

SOURCE: Does my 2001 3.3L V6 EFI Nissan Xterra have a non

It's has a timing belt, also it's an interference engine, if belt goes bad it will bent valve's .

Posted on Nov 24, 2009

  • 36 Answers

SOURCE: I need head bolt torque sequence for 2002 nissan

So 80 degrees is approx. how many ft lbs.

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is 2002 lexus es300 a non interference engine


The 2002 lexus es 300 has the 3.0L engine, which is non-interference. The later lexus es 330 has the 3.3L engine, which is an interference engine. The even later es350 has the 3.5 engine and is back to non-interference as well as having a timing chain rather than a belt. Hope this helps.

Mar 27, 2017 | Lexus ES 300 Cars & Trucks

1 Answer

Where is my fuel filter located 2002 Nissan Altima 3.5se.. I looked in the tank and didn't find an inline filter either.


2002 Nissan/Datsun Altima 3.5L SFI DOHC 6cyl

The Fuel Filter is located: Under hood, driver side, rear engine area, passenger side of master cylinder, mounted in fuel line

Dec 07, 2015 | 2002 Nissan Altima 3.5 SE

1 Answer

Does my 2002 altima have a non interference engine


It is not a non-interference engine. If the timing chain breaks the pistons will crash the valves.

Jul 16, 2013 | Cars & Trucks

2 Answers

Where is fuel filter located in Nissan altima 2002, how can i replace it.


the fuel filter is located in the tank and is non servicable you have to replace the entire fuel assembly in tank its 214.99 at autozone that is the price for 4 cylinder model the 6 cylinder model is not servicable either but may cost a diffrect amout

May 05, 2011 | 2002 Nissan Altima

1 Answer

I own an '05 Altima 3.5L SL with 181K miles. The only maintenance ever performed on this car has been several brake jobs & changed the spark plugs. Does this car have a timing belt or chain that...


Follow your owners manaul, it has all the services needed according to mileage, of course if you havent been following the book, it doesnt do much good, and you are overdue for Coolant, Trans fluid/ filter, belts, filters, ect. Your car should have a timing chain.

Dec 18, 2010 | 2005 Nissan Altima

1 Answer

I need the timing marks diagram for a 2.5L Nissan Altima


Ignore me if I am wrong, but I believe the timing is ECU defined and non-adjustable. To confirm, it has a crank position sensor.

May 25, 2010 | 2002 Nissan Altima

2 Answers

Does my 2001 3.3L V6 EFI Nissan Xterra have a non


It's has a timing belt, also it's an interference engine, if belt goes bad it will bent valve's .

Nov 24, 2009 | 2000 Nissan Xterra

1 Answer

I'acontrol m working on a 2002 nissan altima.


where is the ac relay on a nissan altima 2002

Aug 04, 2009 | 2000 Nissan Altima

1 Answer

Hi pitch buzzing wind sound from nissan altima 2002


POSSIBLE ALTERNATOR INTERFERES WITH RADIO

Dec 30, 2008 | 1996 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...