Question about Chrysler 300C

1 Answer

Brake interlock switch - 300C Chrysler Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 1,975 Answers

Not sure of the question but am pretty sure I will need the year of your 300C in order to try and help....

Posted on Jul 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 merc grandmarkee wont go into park wont start will start if you wiggle in nutral


Park neutral safety switch could be bad , also the shift interlock safety system .
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.
Condition Possible Source Action
  • Shift Interlock System Does Not Release or Lock Properly
  • Circuitry open/shorted.
  • Blown fuse.
  • Damaged stoplight switch.
  • Damaged shift lock actuator.
  • GO to Pinpoint Test A .

PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE OR LOCK PROPERLY A1 CHECK ELECTRON IGN FUSE
  • Check Fuse 5 (5A) located in fuse junction panel.
Is fuse OK?
Yes No GO to A3 . GO to A2 . A2 CHECK FOR SHORT TO GROUND
  • Turn ignition switch OFF.
  • Remove Fuse 5 (5A).
  • Disconnect shift-lock actuator connector C203 located to the right of steering column.
  • Measure resistance of the Circuit 1003 (GY/Y) between the correct terminal of Fuse 5 (5A) and ground.
Is resistance greater than 10,000 ohms?
Yes No REPLACE Fuse 5 (5A). GO to A3 . SERVICE Circuit 1003 (GY/Y) wire between fuse junction panel and shift-lock actuator. A3 CHECK POWER SUPPLY FROM FUSE 5 (5A)
  • Reinstall Fuse 5 (5A).
  • Turn ignition switch to RUN.
  • Measure voltage on Circuit 1003 (GY/Y) wire and ground.
Is voltage greater than 10 volts?
Yes No GO to A4 . SERVICE Circuit 1003 (GY/Y) wire between interior fuse panel and shift-lock actuator. A4 CHECK POWER SUPPLY FROM FUSE 28 (15A)
  • Turn ignition switch OFF.
  • Disconnect connector C2016.
  • Turn ignition switch ON.
  • Measure voltage on Circuit 10 (LG/R) and ground.
Is voltage B+?
Yes No GO to A5 . SERVICE Circuit 10 (LG/R) for open. RESTORE vehicle and RETEST system. A5 CHECK WIRE BETWEEN STOPLIGHT SWITCH AND SHIFT-LOCK ACTUATOR
  • Turn ignition switch OFF.
  • Disconnect shift-lock actuator connector C203.
  • Apply brake pedal.
  • Measure voltage on Circuit 810 (R/LG) wire and ground.
Is voltage greater than 10 volts with brake pedal applied and less than 1 volt with brake pedal released?
Yes No GO to A6 . SERVICE Circuit 810 (R/LG) wire between stoplight switch and shift-lock actuator. A6 CHECK SHIFT-LOCK ACTUATOR GROUND
  • Measure resistance of Circuit 57 (BK) and ground.
Is resistance less than 5 ohms?
Yes No REPLACE shift-lock actuator. SERVICE BK wire.

Mar 30, 2017 | Cars & Trucks

1 Answer

2010 merc gm shift lever stuck in park car will start steering wheel turns


You have a shift interlock problem . What kind of vehicle ? a mercury what ?
Shift Interlock System
The shift interlock system prevents shifting from PARK unless the brake pedal is depressed. The shift interlock system consists of a shift lock actuator mounted on the selector lever. If the ignition switch is in the RUN position, the shift lock actuator is disabled when the brake pedal is depressed.
If the selector lever will not move out of PARK with the key in the ON position and the brake pedal depressed, it will need to be unlocked manually.
Do the brake lights work ?
Visually inspect for obvious signs of mechanical and electrical damage; refer to the following chart:

Visual Inspection Chart Mechanical Electrical
  • Damaged shift lock actuator
  • Damaged transmission control (TC) switch
  • Damaged shift interlock switch
  • Failed fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Damaged wiring harness
  • Loose or corroded connections
  • Damaged shift interlock switch
Symptom Chart Condition Possible Sources Action
  • Shift interlock system does not release/lock correctly
  • Circuitry
  • Fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Brake pedal position (BPP) switch
  • Brake shift interlock actuator
  • Brake shift interlock actuator module
  • Go To Pinpoint Test A .
PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY Test Step Result / Action to Take A1 TEST THE BRAKE LIGHTS
  • Apply brake pedal and view brake lights.
  • Do brake lights illuminate?
Yes
GO to A7 .

No
GO to A2 . A2 TEST FUSE F22 (15A)
  • Key in OFF position.
  • Check fuse: Smart Junction Box (SJB) Fuse F22 (15A).
  • Is the resistance less than 5 ohms?
Yes
GO to A4 .

No
GO to A3 . A3 TEST THE CIRCUIT FOR A SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: Brake Pedal Position (BPP) Switch.
  • Measure the resistance between pin 1 and ground.
    s7n~tr~en~file=n0039468.gif~gen~ref.gif
  • Is the resistance greater than 10,000 ohms?
Yes
GO to A4 .

No
REPAIR circuit for short to ground. TEST the system for normal operation
Do

Jun 19, 2016 | 2010 Mercury Grand Marquis

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

Gear shiftlock no current not working


check brake transmission shift interlock fuse BTSI. check the NSBU fuse.which is the transmission neutral switch.if all is good check brake light switch.make sure brake lights working if not check fuse.when you apply brake that will energize brake transmission shift interlock solenoid.so you can shift out of park.if brake light switch is okay and fuse good.the brake transmission shift shift interlock solenoid could be faulty.

Jul 15, 2013 | Cars & Trucks

1 Answer

Will not come out of park!


The 2001 Kia Sportage is equipped with a brake safety interlock. When you depress the brake pedal you should hear a click coming from the base of the shift lever. The click is a safety interlock which prevents accidental shifting out of park unless you have your foot on the brake. This is the most common cause for the vehicle shifter to be stuck in park. There is a switch that is activated by the brake pedal, the switch in turn energizes an interlock, which makes an audible click, allowing movement of the shift lever out of park position. If you do not hear a click when applying the brake it is most likely either the brake switch contacts or interlock solenoid.

May 23, 2011 | 2001 Kia Sportage

1 Answer

I have a 2004 F150 supercrew 4x4 and it will not shift into park and when I start it I have to put it into neutral any help Thanks


Sounds like the shift interlock circuit has an issue.

This can be 1 of 3 places

1. The fuse for the Shift Interlock circuit. This is fuse #16

2. The shift interlock switch. This is part of the BPP ( Brake Pedal Position ) Switch that also controls the brake lamps. There are 2 switches in the BPP switch, 1 for the shift interlock, the other the brakes. The circuit in the BPP switch for the shift interlock is the Tan w/ Red stripe wire ( from fuse # 16 ) to Pink w/ Light Green stripe ( to the shift interlock solenoid ).
Test both side of this circuit with a meter ( to ground ) you should have power on the Tan w/ Red stripe wire any time the key is in the Start or Run position.
The Pink w/ Light Green stripe wire should have power any time the brake pedal is pressed down.
If you do not have power at the Pink w/ Light Green stripe wire, you need a new BPP switch.
If you have power with the brake pedal pressed on this wire, you need a new Shift Interlock Solenoid.

Jul 05, 2010 | 2004 Ford F150

1 Answer

AFter starting my truck, i sometimes have to wait ...


Could be the Shift interlock solenoid or the shift interlock circuit ( or the fuse for it )
The shift interlock is on the same switch as the Brake Pedal Position switch, it is on the side of the brake pedal, usually has a yellow c-clip retainer on it.

Start by checking the fuse with a meter for power on both pins on the back of the fuse. The fuse is #16.

If the fuse has power on both sides, next check for power at the shift interlock circuit on the switch on the brake pedal.
The circuit is Fuse #16 to a Tan w/ Red stripe wire to the shift interlock switch to a pink w/ light green stripe wire. When the brake pedal is pushed down power should be on both sides of the switch.

If you have power to both sides, I would say the shift interlock solenoid is the issue ( located : steering wheel column ).
If this is a flow through console, the shift interlock circuit also feeds the floor shifter.

May 20, 2010 | 2005 Ford F-150

1 Answer

Transmission will not shift out of park. I pushed brake and the shifter will not move from park with the button on side of shifter pushed in.


CHECK FUSE TO BRAKE LIGHT SWITCH - NEUTRAL SAFETY SWITCH AND BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID.IF BRAKE LIGHTS WORKS.YOUR PROBLEM COULD BE THE BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID OR BAD NEUTRAL SAFETY SWITCH.MAKE SURE NEUTRAL SWITCH FUSE IS GOOD.

Mar 31, 2010 | 1995 Ford Thunderbird

2 Answers

Can not place from park to drive at grear shift


try replacing the neutral safety switch.

Jan 02, 2010 | 2004 Ford F150

2 Answers

2001 Saab 9-3 with automatic transmission will not shift


CHECK BRAKE LIGHT SWITCH FUSE AND BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID FUSE.IF BOTH FUSES ARE GOOD.PROBLEM IS THE BRAKE SWITCH FAULTY OR BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID IS FAULTY.

Nov 01, 2009 | 2001 Saab 9-3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...