Question about Ford Escape

1 Answer

Ford escape bumper change

Can you replace a bumper on a 04 ford escape with a 06-07 ford escape bumper?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 14,379 Answers

No,they are not inter changeable.

Posted on Jul 16, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2008 ford escape. removal of rear bumper cover

Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

2 Answers

I need to know where the oil filter is??

Looking under the car the oil filter is located just behind the front bumper, a little off to the passenger side. Should be one of the first things you see once you get past the bumper.
The link below has a very detailed step-by-step video of the entire oil change process, including locations of the oil drain plug and oil filter. Hope that helps.
2008 Ford Escape Oil Change - Detailed

Sep 19, 2013 | 2008 Ford Escape

1 Answer

2008 ford escape Missing shows number4 miss fire,changed coil and plug on number4, still the same..

It could Be a wire id use a multi meter to check the ohms of your wires. It could be a sensor or the ignition control box. im not sure its hard to say without looking at it.

Nov 26, 2011 | Ford Cars & Trucks

1 Answer

I have a 2002 escape and want to replace the right front headlight. Do you know if the bumper needs to be removed to install light?

When you look at it from the top down you should see 2 adjustment screws. Remove those and the headlight assembly should come out.

Jan 30, 2011 | 2002 Ford Escape

1 Answer

How to replace a fog lamp assembly on 2006 Ford escape

Typically you have to access these from behind the bumper, sometimes there is a trim panel underneath that you can remove to gain access. In some cases to have to remove the bumper to replace the assembly.

Apr 11, 2010 | 2006 Ford Escape

1 Answer

I need to replace the Headlight Lens on a 2001 Ford Escape

You need to replace the whole headlight unit, which requires removing the plastic bumper.

Jun 30, 2009 | 2001 Ford Escape

2 Answers

Need to replace head lamps on Ford Escape 2001,

there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose is a cpoy of the manual to change..good luck

Headlamp Assembly Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Apr 22, 2009 | 2003 Ford Escape

2 Answers

Need to replace headlight assembly on 2005 Ford Escape

ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces are the manuals instructions..

Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Jan 01, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides