Question about 1998 Chevrolet Blazer

3 Answers

1998 S10 ABS light on, blower motor and wiper motor quit working

I replaced the right front fender. I removed the battery and the tray. After reinstalling all parts the truck ran fine. The next day the battery was dead. I charged the battery in the truck and drove the following day. About 15 min into drive the wipers quit working(it was raining), the blower motor quit working and the ABS light came on. I have checked for a pinched wire, I have checked all ground wires, no blown fuses. I cannot figure out what is causeing this issue. the truck runs fine otherwise. Any ideas what to look for?

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chevrolet Expert
  • 242 Answers

FYI......The Early model S-10 has a wiper motor recall...I would go over it again with a fine toothed comb...The odds of blower motor or blower motor resistor..,and the ABS all failing at the same time would be a head scratcher...But it is possible I guess..But I think it HAS to be in the wiring...Disconnect battery then reconnect to reset the computer ..Some relays are hard to check ..most people check fuses and then they say.." all relays are good..".. get owners manual and find blower relay...Does your AC STILL WORK...?..

Posted on Feb 19, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 52 Answers

Get the alternator checked and the serpentine belt condition and tension. Check the specific gravity of the battery.

Posted on Jul 17, 2013

Testimonial: "Battery is new. Alt new."

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Sounds like your computer got wet. Could also be a bad battery, make sure you do a load test and check it. Any auto parts store will check it for free.

Posted on Jul 17, 2013

Testimonial: "Everything under hood seems dry and battery is new."

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: changing wiper motor in chev s10

It's not bad. They make a special tool to remove the motor from the arm assembly, but with a little determination I was able to remove it with out the tool. If your wipers aren't working try running power to the motor first to test it. I swapped it out and the problem ended up being a bad ground in the switch. I bypassed that for a little while by running a jumper wire from the engine block to motor. It also could be the pulse module they are known for going bad in GM vehicles.

Posted on Jan 21, 2009

  • 840 Answers

SOURCE: Rear Windshield Wiper Problems

Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Posted on Jan 31, 2009

  • 366 Answers

SOURCE: 2001 S-10, Blowing "ECM Batt" fuse after running for about 30 min

that fuse feeds power to fuel pump relay circuit that feeds pump could be defective pump,or damaged circuit wires that shorts out! and not a good idea to put higher fuse in circuit could cause more damage to circuit! but i know when your stuck, u do what it takes,so inspect circuit related to fuse,

Posted on Mar 11, 2009

mechanicm639
  • 253 Answers

SOURCE: windshield wipers quit working on 2003 chevrolet trailblazer. relays and fuses are okay.

There were some issues with ignition switches in those vehicles.It is easy to change and does not cost but about $30. Remove the column covers, unplug the switch, and depress the 2 white tabs holding it in place. Good Luck

Posted on May 23, 2009

  • 169 Answers

SOURCE: replaced wiper motor but still won't work buzzes

can you move the linkage when you pulled the motor?

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace alternator instructions


put car on axle stands next very important DISCONNECT BOTH BATTERY TERMINALS then remove under cover,right front wheel and fender liner,bumper and right headlight.next remove fan belt and tensioner disconnect alternator then loosen and remove bolts and remove alternator

Sep 06, 2014 | 2005 Renault Scenic 1.9

2 Answers

How do I remove and reinstall a battery in an 850? (96)


Assuming it's still the factory set up.

Remove the two 10mm bolts that hold the cables on and remove the battery cables (negative/black cable first).

at the base of the battery tray there is a hold down retainer. the retainer is like a half moon piece with a tab that hangs over the base of the battery to lock it in place.

looking at the car it will be on the front left side edge of the battery.
Lift the retainer out using a rotating motion towards the battery while pulling up on it. BE CAREFUL!!! it can take some force to remove and when it does your hand will hit the nearest bracket there.

to reinstall sit the battery into the back edge of the tray like sliding in a baking tray into a low oven. this will allow the battery housing to fit under the back lip of the battery tray.

Slide the battery all the way towards the outside of the fender (towards your right) and reattach the hold down by rotating downwards while pushing down.

reattach the battery cables and you're done. now hopefully you have the radio code... if not go by the dealer and they can get it for you (if you still have the factory radio).

As a side note, if the cables are badly corroded they can be cleaned with normal hot (almost boiling) water and a light brush. we use the hot water out of the coffee maker. when clean apply some battery protector (from any parts store) to keep the cables from oxidizing.

May 06, 2014 | 1996 Volvo 850

1 Answer

Wipers, blower motor will not work, fuses are all good


Electrical system, un connect your battery then reconnect

Dec 12, 2013 | 1995 GMC Sierra C1500

1 Answer

1998 Mercury Mystique heater blower motor doesn't work. Have replaced everything and checked both fuses (both good). What next?


Don't know how the ABS light would be related to the blower motor, you said you checked everything - did you check the blower motor circuit for power and ground with a meter or a test light ?
Is the resistor getting power from the relay ?

Oct 16, 2012 | 1998 Mercury Mystique

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

1 Answer

Abs and brake lights on dashboard are on when they came on my speedometer quit working.also it stalls sometimes while driving and brakes are applied


replace rear sensor and reseat the three plugs at the ECM at passenger front fender under the hood with the battery cable disconnected for at least 10 mins...hook the battery back up and test.

Nov 23, 2010 | 1998 Dodge Dakota

1 Answer

How to change battery


  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
    513051.gif
    tif.gif
  3. Disconnect the battery positive cable terminal bolt from the battery.
    513047.gif
    tif.gif
  4. Remove the battery hold down retainer bolt (1).
  5. Remove the battery hold down retainer (2). Important: Do not tip the battery more than 40 degrees during removal.
  6. Remove the battery (3).
    201375.gif
    tif.gif
  7. Remove the battery insulator from the battery.
Installation Procedure

    201375.gif
    tif.gif
  1. Install the battery insulator to the battery.
    513047.gif
    tif.gif
    Important: Do not tip the battery more than 40 degrees during removal.
  2. Install the battery (3) to the battery tray.
  3. Install the battery hold down retainer (2). Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the battery hold down retainer bolt (1). Tighten
    Tighten the battery hold down bolt to 18 N·m (13 lb ft).

    513051.gif
    tif.gif
  5. Connect the battery positive cable to the battery. Tighten
    Tighten the battery positive terminal bolt to 15 N·m (11 lb ft).
  6. Install the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
  7. Connect the battery negative cable to the battery. Tighten
    Tighten the battery negative terminal bolt to 15 N·m (11 lb ft).

Nov 11, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

How to replace the battery in a 2002 Dodge Intrepid


Hi there. The battery cell in this particular vehicle can be a little tricky to locate.You will first need to remove the right front tire. Next; Remove the right front inner fender liner. Once that is completed, you will expose the battery just to the inside of the right wheel fender liner. You can extract the battery at that point. Remember to remove the Neg- black post first, then, the Red+ positive post last.

Aug 13, 2010 | 2002 Dodge Intrepid

2 Answers

How do you replace the evaporator core for the a/c? on a 1994 gmc p/u truck, I've already have the dash out having promblems removing the duct work, what's next? or is there a maunal that will show me.


your instructions are on how to replace the condenser on a 1994 gmc sierra but the title says it is the directions for replacing an evaporator. please correct your title.

Aug 08, 2010 | 1994 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...