Question about Cars & Trucks

1 Answer

2006 pacifica touring

Transmission is not shifting. 4k rpm at 50mph. When I start vehicle, bell chimes and airbag light lights up, chimes again brake, abs, and wheel track lights turn on. When I shut it off, the gearshift/mileage indicator light stays on. Things I've done: replaced ground wire, ran new hot wire to fuse box (TIPM)...To shut off gear/mileage light I turned #3fuze 180 degrees (IOD fuse).

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Still have same problem.

Posted on Nov 10, 2013


6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 126 Answers

SOURCE: dcs and abs light staying on

car is sensing a problem with the stability control system (DSC) or the antilock brake system (ABS). usually an ABS problem will turn off the DSC, so DSC may be ok, just ABS needs a look at.

since its an '08 model, it should still be covered by the BMW warranty provided you live in the USA. take it in and have them fix it. not safe driving with both systems deactivated.

Posted on Feb 23, 2009

localwonder
  • 6784 Answers

SOURCE: 2006 Chrysler Pacifica touring abs light on stays on

Hi. this light is a warning that concerns the ABS sensor and mechanism assembly. there is a central module and connecting sensors that are attached to each axle/rotor. If any of the sensors become unstable or starts to malfunction, the main module will detect this anomaly and it will trip the light via, the ECM.

I recommend taking this vehicle in so that the ABS techs can diagnosis this issue and they can pin point which sensor or mechanism is malfunctioning.

You vehicle seems to operate in a normal manner at this point but, you will actually have to be in a hard braking situation in order to experience this malfunctions results. If you where to initiate a hard brake while the ABS system is in safe mode(light on), your vehicle would simply lock up. It would not provide the ABS actions due to this malfunction that is evident at this point.

Please rate and god bless:)


Posted on Apr 21, 2009

  • 401 Answers

SOURCE: brake indicator light stays on

Hi the RED BRAKE LIGHT is also for low brake fluid
check the brake fluid level in most cases if the brake fluid is low you need the brakes replaced

Posted on May 08, 2009

  • 599 Answers

SOURCE: Elantra J2-1997- ABS and Airbag light on dashboard stays on

this car needs to scanned for computer codes, the scanner must be capable of scanning asian codes,get back to me when you get the codes

Posted on May 14, 2009

  • 2 Answers

SOURCE: transmission doesnt shift abs & brake light on speedometer doesnt work

I had the same problem with ABS light and speedometer, I was told that it is the transmission control module. It has not yet stopped shifting but I have had times where it just wont stay running. It will start and then stall. Hope this helps.

Posted on May 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix pacifica stuck in park


Are you parked on a significant incline? You may need to have your car CAREFULLY pushed slightly uphill by another vehicle while moving the shift lever. Not on a hill or a light uphill push doesn't help? Check to see if your brake lights are working. If your brake lights do not come on when you depress the pedal, your brake light switch or brake light circuit fuse may be the culprit, as that is where the release solenoid for your gear shift receives its power. Correct the brake light circuit issue and your problem will be cleared.
If your brake lights are working correctly, listen for a light click at the gear shift lever when you depress the brake. If you don't hear one, suspect the locking solenoid is jammed (can usually be corrected with a shot of oil, once you get to it).
Another possibility is that the shift linkage has jammed. Check the linkage for broken parts. It is also possible that the "parking pin" in your transmission has become jammed, especially if the car was run into while parked. If that is the case, you'll need to have the park pin replaced.

Aug 09, 2014 | 2006 Chrysler Pacifica

1 Answer

Will not shift out of park


Check the owners manual for the override procedure. Then have the brake lights checked.

Feb 07, 2013 | 2008 Chrysler Pacifica Touring

1 Answer

My pacifica is stuck in park


1st question, do the brake lights work? The systems lock out solenoid gets power from the bake light circuit, so you can't shift out of park unless the brake pedal are pressed, it senses this through the brake light switch.

May 24, 2012 | 2006 Chrysler Pacifica

1 Answer

Chrysler pacifica is stuck in park


Your vehicle has a brake shift interlock which prevents the vehicle from being moved out of park unless the brake pedal is pressed. I'm sure you know this. If however you have an electrical problem or your computer detects a transmission problem it will prevent you from getting it out of park. I also think (but not 100% sure) that if you have a brake light out that it will prevent you from getting out of park as well. I would check my fuses to start with. There is an over ride and I have posted that below for you so you can at least get it into a gear and drive it until you get the problem fixed. I hope this helps and good luck.


clifford224_487.jpg
clifford224_488.jpg
clifford224_489.jpg

Sep 09, 2011 | 2006 Chrysler Pacifica

1 Answer

1999 jeep grand cherokee tacometer reading???


Cruising rpm even after the OD has engaged has a lot to do with the differential gear ratio and tire size.
There will always be a variation between different vehichles due to that alone.
To see if the OD is working, at about 50mph, lightly touch the brake pedal. If the rpms increase for a moment then the OD was engaged. (touching the pedal momentarily disengages it...good thing to know when hill climbing!

Apr 27, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Check engine light is on. No power, struggle to to obtain 50mph. Power brake and engine surges dramaticly @2500 rpm


Sounds like a fuel system problem, but it's nearly impossible to tell without a computer scan. Have a competent mechanic run a scan and check the vehicle's fuel pressure.

Bill B

Apr 15, 2010 | 2006 Dodge Stratus

1 Answer

Airbag light chiming


Try replacing airbag light fuse. It usu' indicates some damaged wiring if it continues to blink. Also there might be a short in wiring due to water.

Jul 24, 2009 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

2006 Chrysler Pacifica touring abs light on stays on


Hi. this light is a warning that concerns the ABS sensor and mechanism assembly. there is a central module and connecting sensors that are attached to each axle/rotor. If any of the sensors become unstable or starts to malfunction, the main module will detect this anomaly and it will trip the light via, the ECM.

I recommend taking this vehicle in so that the ABS techs can diagnosis this issue and they can pin point which sensor or mechanism is malfunctioning.

You vehicle seems to operate in a normal manner at this point but, you will actually have to be in a hard braking situation in order to experience this malfunctions results. If you where to initiate a hard brake while the ABS system is in safe mode(light on), your vehicle would simply lock up. It would not provide the ABS actions due to this malfunction that is evident at this point.

Please rate and god bless:)


Apr 21, 2009 | 2006 Chrysler Pacifica

5 Answers

PT Cruiser passenger airbag light and bell go off without reason


HI I may have found y the airbag light goes off and on on pt cruisers. there is a pair of wires that connect to the seat air bag pod, the wires run down the seat and to a connector in th floor. after long in vestigation i found that even thou the wires have a conduit protecting them the wires run under the foam pad and over a steel bar, which caused 1 wire to be cut inside yet there was no tell tale sign from out side the sleeve, it was only when I disconected the battery and then the connector from the airbag and the floor connector removed it and run a meter on the two I found it. when i "pulled" the leads the outer sleeve stretched exposing the fault, the wire had a very clean break in it which was odd but the fault. note that only one wire powers the air bag, the other is a feed to the PCM, hence they are connected at the ends hence not easy to trace and with saftey in mind you must not put meters on the wires while connected to any part of the airbag

Dec 07, 2008 | 2007 Chrysler PT Cruiser Touring Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...