Question about 1993 Honda Accord

1 Answer

How to replace serpentine belt on 1995 Honda Accord LX

Okay there are serpentine belts the power steering and the V shaped system one....okay I can get the power steering belt on and give it tension...but how do you give tension to the V-shaped belt after you have removed it? Does it have a tensioner? how do you put it back on? thank you...

Posted by on

  •  Stephen
    Stephen Jul 16, 2013

    I don't show a V belt listed for a 95 Accord with the 4 cyl or V6 engine. Are you sure ? Normally, with a V belt you loosen an idler pulley or the main component depending on what the belt drives.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Alldata.com
old post but here is the answer to that and 10,0000 other questions.

Posted on Feb 02, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ajkill
  • 2035 Answers

SOURCE: Alternater replacement

TO remove :

  1. With the ignition OFF, disconnect the negative battery cable.
  2. Remove the power steering pump. Refer to for the complete procedure.
  3. Remove the cruise control actuator but do not disconnect the actuator cable; simply move the unit out of the way with the cable attached.
  4. Unplug the multi-pin electrical connector.
  5. Remove the terminal nut and remove the wire from the terminal.
  6. Loosen the adjusting bolt; remove the alternator nut.
  7. Remove the belt from the alternator pulley.
  8. Remove the adjusting bolt, the lower through-bolt and the small support stay.
  9. Support the alternator. Remove the upper through-bolt and remove the alternator.
  10. If desired, remove the alternator mounting brackets.
  11. If the alternator brackets were removed, reinstall them. Coat the bolts with a thread sealer or liquid thread lock. Install the bracket bolts and tighten them to 36 ft. lbs. (50 Nm).
  12. Fit the alternator into place. Install the upper through-bolt and tighten it to 33 ft. lbs. (45 Nm).
  13. Install the small stay, the lower through-bolt and the adjusting bolt. Make certain the adjusting bolt is properly installed.
  14. Install the belt. Install the alternator nut. Adjust the belt tension. Tighten the alternator nut to 19 ft. lbs. (26 Nm).
  15. Connect the wire to the terminal and tighten the nut.
  16. Engage the multi-pin connector to the alternator.
  17. Install the cruise control actuator.
  18. Install the power steering pump.
  19. Connect the negative battery cable.15463b8.jpg

Posted on Oct 14, 2008

  • 2 Answers

SOURCE: 1993 honda accord timing belt tensioner

timing belt tensioner should be spring loaded. its tight up there but you'll have to push the tensioner either up or down and slide the belt over it.

Posted on Mar 22, 2009

  • 1 Answer

SOURCE: how does one remove the belt tensioner off a 2001 honda passport?

14 or 15mm socket to release tension. Use socket with leverage bar push/pull towards driver side. Will notice tension releasing, pull belt. Use 5/16 allen wrench for bolt in center, 12 mm socket for mounting bolt. Remove bolts, remove tensioner.

Posted on Jul 06, 2009

philschneide
  • 448 Answers

SOURCE: How do I loosen the tensioner to replace the

First, note how the drive belt is routed, then use a wrench on the tensioner pulley center bolt and turn the tensioner clockwise (four cylinder engine) or counterclockwise (six cylinder engine) to release the drive belt tension. Remove the drive belt from the tensioner and relax the tensioner. Fit the new belt on the other pulleys, then turn the tensioner again and fit the new belt over the tensioner.

The picture is from a different model, but it is similar to what you are working with.

ba64f9c.jpg
Hope this is helpful to you.

Posted on Dec 19, 2009

  • 1340 Answers

SOURCE: how can I replace the serpentine belt?

Tension pulleys are self adjusting.For a belt routing diagram,some local libraries have haynes repair manuals you can look at.A Honda dealer may give you a diagram free or low cost too.Good luck!

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is causing my 1995 Honda accord lx to shake bad after 50 mph. it was not doing it before, it's been doing it for a week and a half or so, any idea what might be causing this? thanx in advance


have a front end and suspension check for loose /worn ball joints , steering rod ball joints , failing wheel bearings
check tires for belt separation , bulges and other defects,including balance
check wheel alignment as it can be castor wobble cause from failing coil springs

Sep 25, 2016 | Honda Accord Cars & Trucks

1 Answer

Need to know where to find a routing diagram for the serpentine belt on a 2000 honda accord lx 4 cylinder


see the following site that I found by googling "2000 honda accord serpentine belt replacement" You will need to know what engine size and whether you have AC.
https://www.google.com/search?q=2000+honda+accord+serpentine+belt+replacement&client=firefox-a&hs=zDs&rls=org.mozilla:en-US:official&tbm=isch&tbo=u&source=univ&sa=X&ei=ylF4UoS5O6zfsAS8oYCgAg&ved=0CFgQsAQ&biw=1280&bih=896

Nov 04, 2013 | 2005 Honda Accord

1 Answer

If timing belt on 1995 Honda Accord LX breaks, permanent damage to engine?


The 1995 Accord LX with the 2.2L and 2.7L, are interference engines. There will most likely be damage if the timing belt snaps.

Jul 23, 2011 | 1995 Honda Accord

1 Answer

I have 1995 Honda accord LX 4 door, it has 135,000 miles. Recently when driving, it is stopping all of a sudden without any warning on the road. It is very scary when car looses it power and stops...


If you haven't had the timing belt done, there is a good chance that the timing belt broke. It is due to be replaced every 90,000 miles along with the water pump. You have an interference engine which means that if the timing belt fails, the valves will hit pistons likely cause damage to the engine. Best case, you get away with having the timing belt replaced. Worst case, you will need an engine.

Jun 14, 2011 | 1995 Honda Accord

2 Answers

How to replace drive belts on 97 honda accord V6. When I put back in the third new serpentine belt on the pulley of the power steering pulley,the belt can not get to the groove, It is blocked by the ...


The power steering pump should have a couple of retainer bolts, and then one adjuster bolt. Loosen the two retainer bolts slightly, then adjust the pulley back out of the way, slip the belt on, and use the power steering pump to tension the system.

Jun 10, 2011 | 1997 Honda Accord

1 Answer

Does the 94 honda accord have a timing belt or a serpentine belt?


Both. It has a timing belt, and a balance shaft belt. Plus it has an A/C belt, Power steering belt, and an alternator belt.

Jun 28, 2010 | 1994 Honda Accord

1 Answer

How do i find the timing belt marks for a 1995 honda accord lx


take the timing belt cover off and look at the cam gears it should tell you the timing marks

Sep 29, 2009 | 1995 Honda Accord

1 Answer

Does a 1996 Honda Accord LX have a serptine belt or a timming belt if it has only on belt in it?


It has both,The serpentine belts can be seen just looking at the engine,While the timing belt is hidden by the timing cover.

Please take time to rate this fixya

May 13, 2009 | 1996 Honda Accord

1 Answer

Replace serpentine belts 95 accord lx 2.2L


While wearing safety goggles and engine switch off.

Your 95 Accord comes with a 2.2L (4 cylinder)
I believe the 2.2L has two belts: power steering and alternator (with or without A/C - different belt applications).
If you are replacing belts note the routing of each one..
. In any case these belts are not easy to replace . Each of the belts has its own manual tensioner. You should have pry bar or lever to push the tensioner back to release the tension on the belt.
There is not a lot of room to work between the pulleys and body of car (the engine is transversely mounted). Slip the belt off any pulley you can reach. Carefully release the pry bar on the tensioner pulley. To replace belt reverse the above step. Do not pinch or crimp the new belt.

You may also want to consider the timing belt also.

Mar 18, 2009 | 1995 Honda Accord

Not finding what you are looking for?
1993 Honda Accord Logo

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...