Question about Nissan Cars & Trucks

Open Question

Brake load sensing valve

Can you by pass the load sensor valve on a 1999 nissan Quest

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: 1999 nissan quest brake pad replacement

Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Posted on Jan 21, 2009

  • 4369 Answers

SOURCE: 2001 brake pad replacement 2001 nissan quest

The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal

  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: volkswagon polo brake load sensing valve is seized

volkswagen polo rear brake load sensing valve linkage has seized!!!
What can i do?

Posted on Sep 03, 2009

  • 1428 Answers

SOURCE: 1999 Nissan Quest washer tank

Visit the site below for the needed parts:-

http://www.autozone.com/autozone/catalog/parts/partsLanding.jsp;jsessionid=A1http://www.autozone.com/autozone/catalog/parts/partsLanding.jsp;jsessionid=A1672379B5D3BFE00C4009668E08563C.diyprod2-b2c3?landingPage=parts&itemId=0-0672379B5D3BFE00C4009668E08563C.diyprod2-b2c3?landingPage=parts&itemId=0-0

Rate this solution.

Posted on Jan 11, 2010

  • 12 Answers

SOURCE: Does the nissan quest 1999 timing belt needs to be

The Quest has a non interference engine meaning that should the belt break the engine would just die without breaking anything. Nissan recommends 105K for changing but that depends on the way the vehicle was driven (driving habits), road conditions etc. If driving on roads for e.g. that are hilly, it labors the engine more thus shortens the lifespan of the belt according to mfg.

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 99 nissan quest radiator fan don't come on at idle or at stop in traffic and this cause overheating only work at low driving speed 20-30 mph


Your water temp sensor might be out of specs that means it sense only certain temperature to start your fan it is like a termoshtat

Jul 13, 2014 | 1999 Nissan Quest

1 Answer

1999 Nissan Quest ABS brake system


Need a code reader & may need a professional scan tool,
to get all the codes/data/etc

Jul 07, 2013 | 1999 Nissan Quest

1 Answer

Where does the knock sensor is located


you have to remmove the intake and it is on what looks like a bracket that bolts to both heads is the knock sensor

May 08, 2010 | 1999 Nissan Quest

1 Answer

My 1999 Nissan Quest is sputtering. What could


go here and the Villager/Quest team will help you.

It could be distributor. 99 was a bad year for this. Bearing makes dust and covers optical sensors in distributor.

could be MAF sensor dirty. clean with carb cleaner. disconnect battery for 2 hours and drive for 10 miles to relearn computer.

http://groups.yahoo.com/group/villagerquest/

Feb 02, 2010 | 1997 Nissan Quest

2 Answers

2001 nissan quest brakes


You need a scan tool to hold open the control valves in the ABS, air is trapped in it and you can't bleed the brakes until you have the ABS held open

Apr 12, 2009 | 1999 Nissan Quest

1 Answer

Brakes?


change the rotors you most likly have a thickness variation causing the brakes to pulsate

Oct 22, 2008 | 1999 Nissan Quest

2 Answers

Brake lights on


I had the same problem with my nissan quest 1996, the problem on mine is caused by a broken plastic cushion on brake pedal, there are two switch sensors under brake pedal, they can be easily seen if you poke your head underneath the front driver seat. I temporarily put a good size screw and nut as a cushion, will get a new one to replace this, nissan put a plastic one instead of metal one for less wear on break sensor switch (I think). Hope this will be help for you.

Jay

Sep 18, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...