Question about Cars & Trucks
There is no pulse on the injectors
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
injector pulse is just controlled by the ecm or computer as some would say,u said u replaced wires? did u have a fire or melt wires? ecm is known to go bad on these,had a few of these trucks back in the day.
Posted on Feb 16, 2009
95-97 Maximas had a problem where condensation from the A/C would accumulate in the a/c evaporator case from the drain becoming restricted or blocked, When this would occur, condensation would drip onto the ECM and a problem would develop with misfire and/or starting. I would look at the ECM where the harness connects to it for corrosion problems. If you find it, there is a chemical spray which can be used to clean the terminals and/or you can clean them, although it is time consuming and difficult to due because of how small the terminals are. After things are cleaned up, lightly coat the connections with a dielectric grease. This will prevent electrolysis.I believe you can buy these at Radio shack and possibly at an automotive parts supplier.
Also a drop in voltage during the cranking phase will cause a weak spark. Your ignition is what pulses the injectors. It takes a minimum of 9.6 volts, but ideally you want at least 10.5 or more during the cranking phase if you want to get a spark worth anything. Check the voltage on the primary side of the coil while cranking the engine.
I'll watch to see if things work out for you, let me know. ....mybunkey
Posted on Apr 18, 2009
Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.
What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.
Code #12: Normal No Codes.
Code #13: Open Oxygen Sensor Circuit.
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High.
Code #21: Throttle Position Sensor High.
Code #22: Throttle Position Sensor Low.
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor.
Code #25: Manifold Air Temperature Circuit Low.
Code #32: EGR System Failure.
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low.
Code #36: Mas Air Flow Sensor Burn-Off Function Fault.
Code #41: Cylinder Select Error.
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control.
Code #44: Lean Exhaust indication.
Code #45: Rich Exhaust Indication.
Code #46: Vehicle Anti Theft Fault.
Code #51: Faulty Mem-Cal.
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low.
Code #53: System Over Voltage.
Code #54: Fuel Pump Circuit Low Voltage.
Code #55: Defective ECM.
Code #62: Engine Oil Temperature Sensor Circuit High.
Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).
If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.
If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.
Good luck and hope this helps.
Posted on May 08, 2009
This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA
Posted on May 15, 2009
Tips for a great answer:
Aug 09, 2017 | Cars & Trucks
Oct 02, 2016 | 2007 Opel Corsa Utility
May 11, 2016 | 2007 Opel Corsa Utility
Mar 06, 2016 | Opel Cars & Trucks
Oct 11, 2015 | 2001 Opel Corsa 1.7
Jan 08, 2015 | Opel Cars & Trucks
Aug 27, 2014 | Cars & Trucks
Mar 30, 2014 | 2001 Opel Corsa 1.0
94 people viewed this question
Usually answered in minutes!