Question about Cars & Trucks

Open Question

Mazda bongo flash code 77

Air bag light flashing intermittently

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: air bag code

Hi, ON your 2002 ford taurus, The Flashing code 33 ( B 2292 )

This code refer to : Driver side seat belt pretentioner ( seat belt bucklet) problem.

Check the conecctions under the driver seat.
Repair as need, and recheck if thi code is present.

But if you had an accident on you taurus. You need to replace the Seat belt Pretentioner ( seat belt bucklet)

OK. I hope this information work for you.

Than's.

Posted on Jul 11, 2008

Ad
  • 142 Answers

SOURCE: Air Bag Code

Code 52 relates to low voltage detected in a capacitor inside the airbag module. 45 seconds after key on, this capacitor should have a voltage of around 23 volts.

This capacitor stores energy to deploy the airbag in the case of a collision.

Because your airbag light is on, your system is deactivated (cannot deploy)

In your case, the airbag computer detects less than 23 volts at that capacitor 45 seconds after key on, and disables the system.

There is a diagnostic procedure involved in fixing this problem, but usually means a bad airbag module (computer)

This should only be checked by a qualified technician, as airbag service can be dangerous and there are strict procedures to follow so the bags don't inflate suddenly and cause injury.

Posted on Aug 27, 2008

  • 4874 Answers

SOURCE: Ford Mondeo Mk3 Estate 2L. Air bag / seat belt Warning Light

Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Posted on Sep 06, 2009

ZJLimited
  • 17970 Answers

SOURCE: My air bag light is flashing. What does that

1. Get in your Pathfinder and CLOSE the door. Turn the key on one click to accessory mode so that all of the other lights on the dash are on but do not start the car. Now open your door and push the the button inside your door jamb that turns your interior light on 7 times. Close your door and then turn your key off.

Now start the Pathfinder...it should be off. If not, repeat this series a couple of times and it will go off. I have had theis happen twice and this is the correct way to fix the problem.

2. Similar story, similar results here too with a 2007 Nissan Pathfinder. Got a new stereo installed, and got a bonus with the blinking airbag light on the instrument panel. Got nowhere with the 7x or 10x domelight press-the-switch voodoo. Bounced into this forum and got the fix that works for my SUV. For the 2007 Pathfinder owners out there: You'll notice the ignition key "beep" is heard only 4 times, not 5.

It took a little patience, as this procedure took me 2 attempts. This is a slight modification from the one mentioned above for the Frontier and the Maxima, but this definitely worked for my 2007 Nissan Pathfinder:

1. Key in, ignition turned to on (but don't start truck).
2. Pay attention to the 4 beeps and watch the dash lights. You're looking for the airbag light to go out just after the last beep.
3. As soon as the light goes out (but BEFORE it begins blinking on you) QUICKLY switch the key back to OFF. Don't remove the key yet.
4. After about 2 or 3 seconds, repeat steps 1 - 3. In total you will do this procedure about 3 times. I say "about" because this all took a couple of attempts, but it was at least 3 cycles.
5. After your last cycle, wait about 5 seconds and turn the key to ON again, and just observe the dash for the airbag light. It should go out and stay out. If not, try it again but maybe add an additional cycle.

Like I said, it took me a couple of attempts but it worked. All credit must go to this website, with special thanks to the poster "LB" ( http://www.carsforums.com/nissan/7423-nissan-airbag-light-reset-fix.html#post65692 )

I hope help you with this. Good luck.

Posted on Sep 14, 2009

  • 1 Answer

SOURCE: flashing code 27 on air bag light

Code 27 is a problem passenger airbag disconnect switch. Usual caused by the bulb next to the passenger airbag on/off key being burned out. Check out this website for instructions on replacing it, you have to solder in a new bulb or replace the whole switch assembly. http://www.automotiveforums.com/vbulletin/t72315.html

Posted on Sep 18, 2009

Testimonial: "solution worked and saved me a 137.00 dollars on a new switch."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code 64 for mazda b3000 2001? Its an air bag


should be the engine light blinking the code flash

paper clip trick on the diagnostic port
no information on 64

if you have an air bag fault needs the obd2 diagnostic reader
to locate the fault ,, fix ,, then reset the srs system

Oct 22, 2016 | Mazda Cars & Trucks

2 Answers

Air bag light flashes code 51.


If your airbag code is blinking, and you get 51, it means that your internal thermal fuse in your airbag computer is blown which is caused by an intermittant short to ground on one of the wires in the circuit. When the short to the ground is removed, code 51 flashes with the use of the airbag warning lamp, 5 flashes, pause, 1 flash, longer pause. According to the Ford, this is a nonrepairable fix, you must buy a new air bag module which is a blue box located in the vicinity of the the steering column.

Apr 10, 2014 | 1994 Ford F150 Styleside Supercab

1 Answer

Ford airbag code 54


94+ AIR BAG DIAGNOSTIC TROUBLE CODES/CLEARING
Code Component/Fault Description

No Air Bag Indicator - Inoperative Indicator Circuit
Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor.
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 RH Radiator Primary Crash Sensor Feed/Return Circuit Open
42 LH Radiator Primary Crash Sensor Feed/Return Circuit Open
44 RH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
45 LH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
52 Intermittent or Repaired Lost Battery Feed
53 Intermittent or Repaired Air Bag Circuit Shorted to Ground
54 Intermittent or Repaired Primary Crash Sensor Circuit Shorted to Ground
61 Intermittent or Repaired Diagnostic Monitor Not Mounted to Vehicle Properly
62 Intermittent or Repaired Safing Sensor Output Circuit Shorted to Battery Voltage
63 Intermittent or Repaired Memory Clear Circuit Improperly Grounded
64 Intermittent or Repaired System Disarm Failure or Internal Diagnostic Monitor Fault
72 Intermittent or Repaired Driver Side Air Bag Circuit High Resistance or Open
73 Intermittent or Repaired Passenger Side Air Bag Circuit High Resistance or Open
74 Intermittent or Repaired Driver Side Air Bag Circuit Low Resistance or Shorted
75 Intermittent or Repaired Passenger Side Air Bag Circuit Low Resistance or Shorted
81 Intermittent or Repaired RH Radiator Primary Crash Sensor Feed/Return Circuit Open
82 Intermittent or Repaired LH Radiator Primary Crash Sensor Feed/Return Circuit Open
84 Intermittent or Repaired RH Radiator Primary Crash Sensor Not Mounted to Vehicle
85 Intermittent or Repaired LH Radiator Primary Crash Sensor Not Mounted to Vehicle
Rapid Continuous Flashing of Air Bag Indicator (No Diagnostic Trouble Code) Both Primary Crash Sensors Disconnected Assembly Plant Mode

TROUBLE CODE CLEARING

1. Follow the diagnostic procedures to service the fault condition flashing on the air bag indicator prior to code clearing.

2. Cycle the ignition switch to OFF and then to RUN.

3. Observe air bag indicator prove-out (six ? two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.

4. Locate the Diagnostic "Trouble Code Clear" Connector (grey connector). located underneath the glove compartment, left side (06010) containing Circuits 631 (T/R) and 57 (BK).

5. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.

6. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).

7. Release short on Circuit 631 (T/R) to Circuit 57 (BK). This short must be released within 25 seconds after the diagnostic monitor tone sounds.

Diagnostic trouble code is now cleared from memory. Next highest priority diagnostic trouble code stored (if one exists) will begin flashing.

The codes and clearing proceedure above are to be used as a guide, NO claims are implied as to the correctness or accuracy of either.

Sep 11, 2013 | Cars & Trucks

2 Answers

What does a flashing air bag light mean on a 1993 Grand Marquis?


A flashing airbag light can mean one of two things. The first possibility is that your battery is in death row. Have it tested at your local parts store. The second possibility is that there is an actual problem with the airbag system. Below is a list of airbag codes, which will flash on the warning light. For example, the light will flash once, pause and then flash twice == 12.


12=Low Battery Voltage
13= Air Bag Circuit Shorted to Ground
14=Primary Crash Sensor Circuit Shorted to Ground
21=Safing Sensor Not Mounted to Properly
22=Safing Sensor Output Shorted to Battery Voltage
23=Safing Sensor Circuit Input Feed/Return Circuit Open
24=Safing Sensor Output Feed/Return Circuit Open
32=Driver Side Air Bag Circuit High Resistance or Open
33=Passenger Side Air Bag Circuit High Resistance or Open
34=Driver Side Air Bag Circuit Low Resistance or Shorted
35=Passenger Side Air Bag Circuit Low Resistance or Shorted
41=RH Primary Crash Sensor Feed/Return Circuit Open
42=LH Primary Crash Sensor Feed/Return Circuit Open
44=RH Primary Crash Sensor Not Mounted to Vehicle Properly
45=LH Primary Crash Sensor Not Mounted to Vehicle Properly
51=Air Bag Diagnostic Monitor Internal Thermal FuseFuse Blown Due to Intermittent Short to Ground
52=Backup SupplyVoltage Boost Fault
53=Primary Crash Sensor Circuits Resistance to Ground or Air Bag Diagnostic Fault


Hope this helps...

Jul 23, 2011 | 1993 Mercury Grand Marquis

3 Answers

Flashing airbag light on 97 maxima. Car was in an accident, airbags deployed, replaced bags and controller why won't the light stay off


To manually check air bag codes, turn the key On and push the driver's door switch (at the bottom of the B-pillar) 5 times or more within 7 seconds of turning the key ON. Then watch the air bag light flashing codes. The air bag light will come ON for 3 seconds and then give fast flashes if there is a code. Count the fast flashes as the code. So the air bag light on for 3 seconds and then 8 flashes is a code 8 for the passenger air bag circuit. after counting code clear codes and see if they come back

Nov 22, 2009 | 1997 Nissan Maxima

1 Answer

Air bag light keeps flashing!!!I have a 1999 mazda 626 2.0


The air bag light flashing is indicating the SRS module has detected a failure in the air bag system. It could be anything from a sensor to bag module or wire connection.
I would take your vehicle to your local Auto Zone or Advance Auto and ask them to scan your car for trouble codes, they will do it for you at no charge, write the codes down and respond back and we can begin to diagnose the problem.
Good luck.
Regards,

Aug 27, 2009 | Mazda 626 Cars & Trucks

2 Answers

My air bag light on my 2000 Ford Econoline van flashes a 19 code. Does anyone know what that means?


Seems to be a very common problem with Ford. The wiring harness beneath the drivers seat contains the sensors for the airbag system. Go under the drivers seat and secure all the wires and clips. This makes most error lights for the airbags go away. Hope this helps and good luck!

May 02, 2009 | 1996 Ford Aerostar Extended

1 Answer

Air bag sensor keeps flashing


If a concern is detected, the air bag control module will communicate by flashing the warning indicator. A diagnostic trouble code (DTC) is logged by the air bag control module in a nonvolatile memory. For additional information, refer to Diagnosis and Testing in this section.
Lamp Fault Codes (LFC)
Item Part Number Description 1 One flash cycle: Driver air bag trouble code 2 Two flash cycle: Passenger air bag trouble code 3 Three flash cycle: Trouble code common to both driver and passenger air bag circuit 4 Four flash cycle: Safety belt pretensioner trouble code common to both driver and passenger pretensioner circuits 5 Five flash cycle: Driver side air bag trouble code 6 Six flash cycle: Passenger side air bag trouble code 7 Not used 8 Not used

Apr 10, 2009 | 2001 Ford Focus

2 Answers

SRS light now repeatedly blinks 5-1 problem code - stop/reset?


Sounds like an air bag problem. You will not be able to reset the light without fixing the problem. The steering wheel airbag electrical contact is suspect. Airbag will have to be removed and problem repaired. . I do not recommend you repair the problem unless qualified.

Mar 12, 2009 | 1998 Lincoln Mark VIII

1 Answer

Airbag flashes 10 times misses a flash then repeats


Try clearing the codes & see if it returns. I do not see a code fault 10. Starts at 12.

---------------------------------------------------------------------
Section 01-20B: Restraints, Passive — Supplemental Air Bag System 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual DIAGNOSIS AND TESTING Diagnostic Trouble Code Clearing Procedure to Clear Diagnostic Trouble Codes from Diagnostic Monitor Non-Volatile Random Access Memory.
Normal Operation
The air bag diagnostic monitor (14B056) continually checks the air bag system for readiness. When a fault condition is detected, the DTC associated with that fault is stored in the air bag diagnostic monitor's Non-Volatile Random Access Memory (NVRAM). After writing the DTC to NVRAM, the air bag diagnostic monitor signals the fault by flashing the appropriate diagnostic trouble code on the air bag indicator. The diagnostic trouble code written to NVRAM is permanently stored in the air bag diagnostic monitor until cleared by the diagnostic trouble code clearing procedure.
  • Upon each cycle of the ignition switch (11572) , the air bag diagnostic monitor checks for diagnostic trouble codes written in NVRAM. If any diagnostic trouble codes exist in NVRAM, the air bag diagnostic monitor will then check to see if these fault conditions are still present.
  • If the conditions of the diagnostic trouble code in NVRAM are still present, then the air bag diagnostic monitor will use the air bag indicator to flash out the diagnostic trouble code number that was written in memory.
  • If the conditions of the diagnostic trouble code are not still present (indicating an intermittent or serviced fault), the air bag diagnostic monitor will use the air bag indicator to flash out a DTC which is the sum of the diagnostic trouble code in NVRAM plus 40.
Example: Due to corrosion, high resistance develops on the driver side air bag circuit. The air bag diagnostic monitor stores a diagnostic trouble code 32 in NVRAM. Upon each cycle of the ignition switch , the air bag diagnostic monitor checks the resistance of the driver air bag circuit.
  • If the resistance is still high, the air bag diagnostic monitor causes the air bag indicator to flash out a DTC 32.
  • If the resistance falls within the normal range due to service or an intermittent condition, the air bag diagnostic monitor causes DTC 72 to be flashed on the air bag indicator.
Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVRAM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (TAN/RED STRIPE) to Circuit 57 (BLACK). This short must be released within 25 seconds after the diagnostic monitor tone sounds. Diagnostic trouble code is now cleared from NVRAM. Next highest priority diagnostic trouble code stored in NVRAM (if one exists) will begin flashing.

Feb 09, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...