Question about Hyundai Santa Fe

Open Question

Intake manifold runner control - Santa Fe Hyundai Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 449 Answers

SOURCE: ENGINE LIGHT ON SLIGHT LOSS OF POWER AND POSSIBLE RATTLE

p2004 (Intake Manifold Runner Control Stuck Open)You need to take a look at the IMRC actuators on the intake manifold. You can try using a screwdriver or other tool to move the actuators to see if one is stuck in the open position. Do not use your fingers to do this, because if one is open and decides to close it has a bit of force behind it and can injure you. If the IMRC is stuck open, it is usually due to deposits in the intake manifold. Repair involves removing the upper intake manifold and cleaning out any deposits in the IMRC plate area. I would try running some Techron Concentrate in 2 tanks of gas to see if it dissolves enough of the gunk on the plates to free up the stuck one. Certainly a lot cheaper than having to pull the intake manifold and cleaning the plates. Always run tier one gasoline like Shell or Chevron to reduce the buidup of deposits.

Posted on Dec 19, 2008

daves944
  • 1050 Answers

SOURCE: I have a '96 Ford Windstar 3.8L & getting OBDII P1537 code.

A common problem on Windstars, there are two IMRC valves, the only way to fix them is replacement, which is not that hard. They are mounted on the end of the intake manifold and control runner length. There is a front and rear one, I'm not sure which one this is but you'll probably have to go to Ford to buy it and they should be able to tell you with the code number. The problem will not affect driveability that much, but if you have emissions testing at your location, this will likely cause it to fail.

Posted on Apr 05, 2009

Hrnsly
  • 154 Answers

SOURCE: Intake manifold runner control stuck closed?

you don't have to replaced the manifold just the runner control. see this all the time at work the part is about 175.00 and an hour and a half to install. your local dealer should be able to fix this for you

Posted on Aug 07, 2009

  • 14036 Answers

SOURCE: 1998 ford windstar 3.8 with code p1538. Is this a

LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Posted on Oct 23, 2009

  • 1 Answer

SOURCE: water leak under the intake manifold,1995 toyota 4 runner

There is a heater core bypass pipe that runs from the block (under the manifold) to the bacl of theengine where you will see a flat rectangular "sheet metal" thing with a pipe coming out of it. The a rubber hose connects. You need to pull the top air plenums and intake to get to it. The p[ipe flange bolts to the block with silicone rtv as a sealant.

Posted on Nov 27, 2009

Testimonial: "thanxs"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

1 Answer

Where can I get a diagram of the intake manifold runner control?


Do a Web search under the terms (Your make, model, year vehicle) intake manifold runner. Or intake runner control solenoids, rods, etc. You may find Youtube videos.

The runners are sandwiched under or inside the intake manifold. Some had plastic clips which crumbled and the operating rods became disconnected. Some runners stuck too bad for the rods to move them.

Jun 30, 2015 | 2003 Ford Mustang

2 Answers

When you have an extremely high idle and code p2008 shows up what could the problem be


Without knowing what car you have it gets difficult to be specific, however since usually p2008 is dealing with intake manifold runner control, and you have a high idle...Id say you may possibly have a loose or broken vacuum hose to runner control...with the vacuum off the runners cant be regulated...and the air leaking in through the bad/open hose will raise idle. check vacuum hoses and runner linikage

Apr 13, 2015 | Cars & Trucks

1 Answer

How do you fix a intake manufacture runner control thats stuck open


I not familiar with a "intake manufacture runner control". Do you mean intake manifold? Not you sure what a runner control is though. Could give us some more detailed information?

Jun 13, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

Chhrysler sebring 2007 2.4 litter getting code p2004 intak manifold runner control how do you fix it


code p2004 refers to intake manifold air control actuator bank 1---actuator stuck open===causes --wiring--intake manifold air control actuator --mechanical fault.
also refers to intake manifold air control solenoid bank 1 solenoid stuck open===causes--wiring intake manifold air control solenoid --- mechanical fault
you may be able to remove and clean the units to ensure they move freely otherwise replace them

Dec 31, 2013 | Cars & Trucks

1 Answer

Replace IMRC Runners on 2006 Fusion


There are two Intake manifold runner control solenoids they are at the base of the intake manifold. they use manifold vacuum to control them with a blown diaphragm they set codes usually a left or right control. only 1 bolt holds them to the manifold and linkage rod controls the internal throttle plates

Nov 06, 2013 | 2006 Ford Fusion

1 Answer

Ford F140 4.2 Do Engine codes P0305, P0306, and P1518 relate to each other


I am assuming you mean F150 truck.
The answer is maybe.
Code 305 and 306 are missfire codes for cylinders 5 and 6.
Code 1518 is for a problem with the intake manifold runner control which could cause the other two codes.

P1518 FORD Description The Intake Manifold Runner Control (IMRC) is monitored for failure during continuous or key ON engine OFF self-test.
Possible causes - Intake Manifold Runner Control (IMRC) harness is open or shorted
- Intake Manifold Runner Control (IMRC) circuit poor electrical connection
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Engine Control Module (ECM)
Read more: http://engine-codes.com/p1518_ford.html#ixzz2KSN6Thui

Feb 10, 2013 | Ford Cars & Trucks

1 Answer

P2006 ford f150


This Code means that the Intake Runner Control on Bank One is stuck closed. An intake runner is a part which acts like a gate and diverts airflow inside the Intake manifold.

Some have control rods which attach with plastic clips and the clips break causing the control rod to unseat in its place. They may use solenoids that are electric or Vacuum controlled and the rods on these devices are what moves the runners.

Often you can take the intake manifold off and clean the runner or reattach the rods.

Please rate my info.

Jan 18, 2013 | 2004 Ford F150

2 Answers

Intake manifold runner control stuck closed?


you don't have to replaced the manifold just the runner control. see this all the time at work the part is about 175.00 and an hour and a half to install. your local dealer should be able to fix this for you

Aug 01, 2009 | 2000 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...