Question about 1991 Oldsmobile Ninety Eight Regency

1 Answer

How to replace the fuseline in back of my motor on a 91 old

I have a pin hole in my line... the gas come out of the line which is in back of the motor...can you put tape on this line

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 2,095 Answers

NO!!!!!!!!!!!!!
it's a pressurized hose. gotta do it right and buy the correct hose

Posted on Jul 15, 2013

Testimonial: "Yes, thank you"

  • kilaakins1 Jul 15, 2013

    Is this Job better for me to do or got to a shop?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 91 s10 with a gm8672235 manual transmission. There is a hole behind the slave cilynder is this normal?


There should be an inspection hole on the housing to line the slave cylinder pin up with the throw out . there's usually a bolt there to keep dirt out but its not the end of the world if there's not

Jan 23, 2015 | 1991 Chevrolet S-10

1 Answer

Gas leak from line on top of motor 91 ford explorer


if it is the rail you will need to replace it with another but if actually is a line you can either replace it with a new one or replace the bad section with a piece of neoprene hose

Mar 03, 2013 | Ford Explorer Cars & Trucks

2 Answers

91 saturn SL2 started leaking trans fluid between the bell housing and motor it is a 5 speed


You have a transmission front seal that has gone bad. The transmission will have to be removed and new seals installed.

Feb 14, 2010 | 1991 Saturn SL1

1 Answer

Sagging door


The easiest way to check for sure is to open the door and lift up. If the door moves an inch or two but not the truck, they are loose. Look around carefully at the hinge to see if the holes are out of round. If they appear to be then get oversize bushings when you get the new pins. They aren't hard to do but you will need a helper. The door needs to be supported while you drive the pins out, I use an old bumper jack but any jack will do the trick. The helper steady's the door so it doesn't twist. There should be a clip on one end of your pins and you probably won't be able to save it so pick up new ones when you get the new pins. with the clips off use a hammer and punch and take the old pins out and the door off. If the holes are ovaled then you will need to **** them out for the bigger bushings. Just remember that the holes will be worn opposite, the top hole at the back and the bottom hole at the front so ram the opposite way and check it often.Your pin doesn't have to be perfectly straight but close. The top hole is usually the worst. When you put the door back on, if you couldn't save or get new clips just put the top pin in so the head is up and you should be okay.
If you have to take the hinge off to drill it the trace out its exact position on the door frame before you remove it so your door will line up when you put it back on. Hope this helps.

Jan 18, 2010 | 1995 Chevrolet G20

1 Answer

Im trying to get the timing marks aligned and dont know where to align them to. Its my neighbors car and he doesnt have a service manual. Someone else tried replacing the timing belt for him and didnt...


with the timing belt on the vehicle install the botton piece of the timing cover with crank pulley. line up the notch on the crank pulley with 0 on the timing cover for top dead center on the crank. then there is a small sight hole in the spokes on the camshaft timing gear. with the belt off the timing gear line up that sight hole with a notch behind the gear on the cylinder head. you will only be able to see the notch through the sight hole with a mirror. once these are lined up slide the belt back on the timing gear and recheck afterward. this the procedure for all 5s-fe motors

Nov 12, 2009 | 1991 Toyota Celica

3 Answers

Unsolved Problem!


Have you looked at the gas or gas tank. It could be full of water. Your specific pump could be sitting up high where the gas water line settles after a period of time. Try some dry gas and run the tank out.

Jul 19, 2009 | 1996 GMC Sonoma

1 Answer

Replacement of fuel pump on 91 firebird


i suppose this would work but then u would have water and debris blowing in and it would rust out. i would rather put 3/4 copper pipe into gas opening and slide rubber line through pipe past flap into gas tank and siphon gas into buckets and lift car on jacks and get a buddy to help lower tank or use floor jack and block of wood to lower tank and not destroy floor and create new problems

Jul 08, 2009 | 1991 Pontiac Firebird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...