Question about Ford Taurus

Open Question

How to change a #2 ignition coil in a 2008 ford taurus 3.5l v6

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

clitradr
  • 2 Answers

SOURCE: ignition switch in a 1995 ford taurus

Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.

  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Posted on Feb 15, 2009

joe7379
  • 93 Answers

SOURCE: 2001 ford taurus wont start

It could be bad plugs, plug wires, a bad ground will do this as well. Check to see if it has the three main things.

Spark
Air
Fuel

Anther common problem is the crank shaft speed sensor. It will cause it to not spark and not start.

Joe

Posted on May 19, 2009

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

  • 15 Answers

SOURCE: Cylinder #1 misfire on a Ford Taurus SHO

Did you check the condition of the spark plug? If the plug is good do a compression check; a very low reading could indicate a sticking intake valve (sticking open). The easyest and cheapest way to fix a sticking valve is to introduce 1/2 can of Sea Foam into the air intake manafold; just follow the instructions on the can except you will use 1/2 can instead of 1/3 can. That Yamaha motor from what I have found collects tons of gunk on the valve stems. Good luck.

Posted on Feb 19, 2010

  • 172 Answers

SOURCE: ford taurus v6 duratec vacuum hose diagram

under the hood is a vacum diagram

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 Ford Taurus SES 3.0 DOHC V6. I have 3 misfires codes P0301, P0304, P0316 (Startup). Changed all 6 ignition coils & spark plugs, and fuel injector on 4. Low gas mileage. O2 Sensor?


i think its the ecu, i had misfire codes come up in my 06 explorer, changed everything like you did, it was the ecu, i got one on ebay with keys for 150, it worked, also ford systems require a fully charged battery

Jun 09, 2017 | Ford Cars & Trucks

1 Answer

SE w/A/T. Why does it go only 10 to 25 mph?


2002 Ford Taurus SES won't go over 30MPH and it won't pass first ...

www.taurusclub.com > ... > Maintenance and Repair
Dec 30, 2011 - Drives: 2002 Ford Taurus SES 3.0L V6 Automatic. Posts: 2 ... I tried your advice about 10 minutes ago and drove on 1, backed out of my driveway on to the main road. Once it .... Goes to 3000 4000 rpm's and only 40 mph. Shake at 60 mph and up
Jan 1, 2013
Wont rev over 3500 or go over 25mph
Jan 9, 2012
Will Changing The Throttle Position Sensor Fix My Problem ...
Feb 2, 2008
Top Speed 45 Mph?
Apr 19, 2004
More results from www.taurusclub.com

94 taurus will not go faster than 15 mph - CarGurus


Jan 01, 2016 | 2002 Ford Taurus

1 Answer

How do I replace coil pack?


Unplug and unscrewed the old one, reverse to assemble. Google replace ignition coil 2000 Ford Taurus and your engine size, like 3.0 V6.

Nov 13, 2015 | 2000 Ford Taurus

1 Answer

2008 Taurus 3.5L V6 SEL Air Intake Removal Procedures for #2 Coil Replacement


You can probably get this manual from your local library.

Nov 14, 2013 | 2008 Ford Taurus SEL

1 Answer

How do i change the ignition coil on my ford taurus


orrect answer I'll need to know which engine you have, you have three choices

3.0L V6 DOHC
3.0L V6 OHV
3.4L V8 DOHC (SHO Only)

Jul 11, 2012 | 1999 Ford Taurus

1 Answer

LOOKING FOR THE LOCATION OF THE LOCATION OF THE IGNITION COIL FOR A 2008 FORD TAURUS MODEL


3.0 DOHC has six individual coils. One for each cylinder. you will see three in the front for the front three cylinders. The upper plenum will need to be removed to get at the back 3. Not a big deal, a couple of connectors, a couple vacuum lines, and a dozen bolts and it comes right off.

3.0 OHV will have a coil pack mounted on the front valve cover. It will have six ignition wires coming out of it.

Oct 27, 2011 | 2008 Ford Taurus

2 Answers

Can't get the starter out of a ford Taurus 2004


either you took out the wrong bolt by the trans.... or the pin is stuck ... give it a whack with a mallet
should of taken out 2 ,13 mm bolts

Jul 28, 2011 | 2008 Ford Taurus X

1 Answer

Negative wire on coil to hook up tach on 1995 taurus gl 3.8 v6.. tach instructions say i need to hook to negative side on coil for pickup...but diagram is for older or traditional ford coil... one negative...


If you have a good look at the coil, it should still have a positive and negative sign on it somewhere. Try not let the extra wires confuse you too much. These are for the ignition module in the distributor. let me know if you need further clarification after you've had a look.

Apr 02, 2010 | 1995 Ford Taurus

1 Answer

Ford engine firing order v6


V6 Cylinder numbering:

1 - 2 - 3
4 - 5 - 6

(Front of Vehicle)

The coil pack looks like this

--4 pin--
-----------------
--1--- 2--- 3--
----------------
--5--- 6--- 4--
----------------- Coil: with the connector positioned in the lower right hand corner, the upper row from left to right is: 4-6-5. The lower row is 3-2-1.

Oct 13, 2009 | 1999 Ford Taurus

1 Answer

2002 Ford Taurus 3.0 V6 DOVC No Fire


check timing,connector,fuel pressure,good luck n drive safe

Jun 05, 2009 | 2002 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...