Question about Cars & Trucks

Open Question

Bleed screw radiator where is it located on a 1996 ford taurus gl

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 1996 ford taurus GL

The air bag module monitors all of the electrical circuits of the air bag system. If it detects a fault in any of these circuits, it will cause the air bag light to come on. If it's flashing, count the number of flashes between pauses, this should be the diagnostic code the module is telling you what is wrong with the airbag system (or you can use a scan tool) The only way to keep the light off (besides removing it from dash) is to repair the fault, you can clear the code with the scantool, but it will come right back on if it still sees the fault.

Posted on Oct 01, 2008

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

c17hydro
  • 2984 Answers

SOURCE: how to bleed the brakes for 2001 ford taurus

Please don't forget to rate:


Bleeding The Brake System Bleeding When any part of the hydraulic system has been disconnected for repair or replacement, air enters the lines causing spongy pedal action (because air can be compressed and brake fluid cannot). To correct this condition, it is necessary to bleed the hydraulic system to ensure all air is purged.
Always begin bleeding the brake system from the furthest wheel cylinder or caliper from the master cylinder; the right rear.
NOTE: The right side of the vehicle is the passenger side. The sides of the vehicle are determined from the driver's perspective. This reference is taken from sitting in the driver's seat, facing forward.
Maintain a full reservoir during the bleeding operation. Never use brake fluid that has been drained from the hydraulic system, or from an open container, no matter how clean it is. Always use brake fluid from a new, sealed container. The front and rear reservoir will drain as the front or rear brakes are bled.

  1. Park the vehicle on a level surface. Place the vehicle in PARK (automatic) or REVERSE (manual) with the engine OFF, and apply the parking brake. Chock the rear wheels to prevent vehicle movement. NOTE: Wheel chocks may be purchased at your local auto parts store, or a block of wood cut into wedges may be used.
  2. Loosen the lugnuts from all four wheels, but do not remove the lugnuts until the vehicle is raised and supported properly.
  3. Use an approved jack and raise the vehicle high enough to place jack stands under all four corners of the vehicle. Place the jack stands under the frame or axles of the vehicle. Ensure that the front of the vehicle is raised higher than the rear.
  4. Remove the wheels from the vehicle.
  5. Clean all dirt from around the master cylinder fill cap. Remove the cap and fill the master cylinder with brake fluid until the level is within 1/4 in. (6mm) of the top edge of the reservoir.
  6. Clean the bleeder screws at all four wheels. The bleeder screws are located on the back of the brake backing plate (drum brakes) and at the top of the brake calipers (disc brakes).
  7. Attach a length of rubber hose over the bleeder screw and place the other end of the hose in a plastic jar.
  8. Have an assistant place and hold pressure on the brake pedal.
  9. Open the bleeder screw 1/2 - 3/4 turn. As the bleeder is opened, the brake pedal will travel to the floor. Have the assistant inform you when the pedal has bottomed out. NOTE: Do not remove pressure from the brake pedal once it is bottomed out. No movement to the pedal should occur until the bleeder is closed and the assistant is made aware of the situation. Failure to do this will draw more air into the system.
  10. Close the bleeder screw and tell your assistant remove their foot from the brake pedal. Continue this process to purge all air from the system.
  11. When bubbles cease to appear at the end of the bleeder hose, tighten the bleeder screw and remove the hose.
  12. After bleeding each wheel, check the master cylinder fluid level and add fluid accordingly.
  13. Repeat the bleeding operation at the remaining three wheels, ending with the one closet to the master cylinder. The pattern is, RR, LR, RF, LF.
  14. Fill the master cylinder reservoir to the proper level and install the reservoir cap.

Posted on Jul 22, 2009

  • 33 Answers

SOURCE: locate ignition control module on 94 ford taurus

It is mounted on the side of the distributor on the right side of the motor as you are facing it.

Posted on Oct 10, 2009

  • 1986 Answers

SOURCE: Adjust (aim) headlights on a 1990 Ford Taurus

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GL model. What are the specs for brake lines and fittings


Hi Audrey, Just tell the sales person at the auto parts store you need brake pads for a 1996 gl ford taurus and they'll look up the parts for you, I hope this helps..........CHEERS..

May 07, 2016 | 1996 Ford Taurus

2 Answers

Iv got a '96 ford taurus gl. When bleeding the brakes is there a certain order they should be done in?


Passenger rear, driver rear, passenger front, driver front, hope this helps

May 07, 2016 | Ford Cars & Trucks

2 Answers

How to change a radiator on a 1996 ford taurus


  1. Step 1 Drive your Ford Taurus up a set of ramps onto a pair of jack stands, if it is a 1996 model or newer. Remove the lower splash shields. For 1986 through 1995 models, you can remove all necessary components from above.
  2. Step 2 Begin by disconnecting the negative battery terminal and draining the radiator into a transportable container. Open the plastic draincock on the lower rear of the radiator and crack the radiator cap.
  3. Step 3 Remove the overflow tube from the coolant recovery bottle and disconnect it from the radiator. On SHO model engines, remove the recovery bottle as well. Next unscrew the shroud and remove it from the retaining clips. Disconnect the wires to the fan motor, and remove the fan assembly and shroud in one piece.
  4. Step 4 Squeeze the hose clamp ends together on the radiator side, and remove the upper and lower hoses. For automatic transaxle models, use either the custom Ford disconnect tool T82L-9500-AH or two crescent wrenches to remove the transmission coolant lines.
  5. Step 5 Disconnect the radiator supports. 1986 through 1992 models will have two upper retaining screws for 3.0 liter and SHO engines. 3.8 liter engines will have two driver's side hex nuts and two passenger side screws. All other models have either the upper screws or the combination of right hand hex nuts and left hand screws.
  6. Step 6 Tilt the radiator backwards toward the engine and lift it out. Fit the new radiator into the support and replace the support screws and nuts. Reattach the hoses and wires in reverse order.
  7. Step 7 Flush the new radiator with either water or a commercial flush treatment. Connect your battery terminals and replace the coolant and let the engine idle for 5 to 10 minutes with the heater on and the radiator cap removed. Top off the coolant as necessary.
Thank you,
Lee

answer found here:
http://www.ehow.com/how_4506379_replace-radiator-ford-taurus.html

Aug 10, 2010 | 1996 Ford Taurus

1 Answer

I need a fusebox diagram for a 1996 ford taurus


For Fuses Location and Description, review the Taurus Owners Manual (page 125 and next).

I hope help with this (remember rated this help) Good luck.

Dec 15, 2009 | 1996 Ford Taurus

3 Answers

Where do i add radiator stop leak in a 2001 taurus


Remove radiator cap with engine cold, remove enough fluid so it can be replaced with stop leak. Add all stop leak & top off with anti freese. Put cap back on & start engine. Run engine for at least 20 minutes or take for a drive. Leak should stop if not too severe.Hope this advice helps if so rate accordingly. Good luck!

Nov 18, 2009 | 1996 Ford Taurus

1 Answer

96 ford taurs VSS


The trick is to snake your arm down the back, ajacent to the maifold pipe, and unplug the wiring harness. Should be a 10mm socket to unscrew the bolt that holds the sensor in place. Once the screw was out it was easy to pull the sensor out and rush to Auto Zone and get a new one. Reverse the process in putting the sensor in.

Jul 15, 2009 | 1996 Ford Taurus

1 Answer

Overheating engine in 24 valve 96 ford taurus 6 cyl


the thermostat can be easily changed from up top, the T-stat is located at the engine end of the upper radiator hose under the flange the hose connects to. Make sure u follow manufacturer's cooling system bleeding procedures when you refill after the T-stat is changed out.

Jun 14, 2009 | 1996 Ford Taurus

2 Answers

Need to locate radiator cap on 1996 ford taurus


It's on top of the radiator. Don't add stop leak to the reservoir, it will only create other problems.

Dec 21, 2008 | 1996 Ford Taurus

3 Answers

1995 Ford Taurus brake pad replacement


the piston need to be turn clock wise and push at the same time make sure when you turn it the rubber around the piston dont get damaged it stick to the piston and get torn before you turn just make sure it not sticking to the piston at the auto part store they sell the toll to turn the piston its cheap$$ hope it FIXYA our post thanks pierre

Jul 06, 2008 | 1995 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...