Question about Cars & Trucks

1 Answer

Grinding noise when starting '98 Izuzu Rodeo

I recently bought a '98 Izuzu Rodeo (sorry for not knowing the engine size). Last week while driving home it started to make a grinding noise. I was able to get the car to limp home. Now when I start the car, it starts to make the grinding noise after a few seconds. Ignition is strong, and when the grinding noise starts the engine will cut off after a few seconds. Will upload a video to see if that will help.

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,246 Answers

Upload video please then i might have a better idea

Posted on Jul 15, 2013

Testimonial: "Thanks for the reply Colin, I think the video is attached as a comment. In case its not showing up, here's the Youtube link. http://www.youtube.com/watch?v=uzNw016gpBM"

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Sgt Fluffy
  • 157 Answers

SOURCE: grinding noise about 30 seconds after starting

Sounds like starter isn't disengaging, get that checked pronto, you could be damaging the flywheel (very expensive). Could be any appliance also; a/c compressor, idler pully, alternator, etc. Don't wait.

Posted on Jun 10, 2009

emissionwiz
  • 76846 Answers

SOURCE: car won't start but makes a grinding noise like when the car is started already

This sounds like a damaged starter drive gear and engine flywheel gear.

Posted on Feb 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 98 Jeep Grand Cherokee used cruise control last week made a grinding noise I turned it off truck went slow for a few now it will not accelerate past 50mph what could be wrong?


Nothing in the cruise control system to make a grinding noise. It is electronic or maybe with yours vacuum controlled. Or a little of both. This could just be coincidental. If it did die, it wouldn't keep you from going faster than fifty. Have the engine and transmission codes read.

Jun 13, 2016 | Jeep Cars & Trucks

1 Answer

98' ISUZU RODEO SOUNDS FROM THE ENGINE !!!!!!


Go to any shop and have them listen.

Nov 05, 2012 | 1998 Isuzu Rodeo

1 Answer

Its a 01 izuzu rodeo,engine hesitates constantly and the radiator smells like gas,and it gets hot real fast


sorry only one thing will cause this and i think you know the answer ,HEAD GASKET

Jan 07, 2011 | 2001 Isuzu Rodeo

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

1 Answer

Grinding noise about 30 seconds after starting


Sounds like starter isn't disengaging, get that checked pronto, you could be damaging the flywheel (very expensive). Could be any appliance also; a/c compressor, idler pully, alternator, etc. Don't wait.

Jun 10, 2009 | 2007 Dodge Charger SRT8 Sedan

1 Answer

Where is the thermostat on a 98 izuzu rodeo v6


Generally, it's where the upper radiator hose meets the engine block.

Jun 07, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...