Question about Cars & Trucks

Open Question

Rear diff pinion oil seal removal on Acco 1950c tipper truck

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

  • 92 Answers

SOURCE: pinion seal leaking

check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Posted on Oct 22, 2008

BCally1
  • 133 Answers

SOURCE: rear pinion seal replacement

with a puller

Posted on Jan 13, 2009

emissionwiz
  • 75822 Answers

SOURCE: leak at rear diff (pinion seal?) 03 4X4 ford ranger

the part is called the pinion flange seal, pull the drive shaft, remove the large nut on the flange the drive shaft connects to and remove the flange, then pry out the old seal and lube the lip of the new seal with motor oil and press it into the opening. The 7.5 hour estimate is way wrong, about 1.5 hours labor and $4 for the part.

Posted on Apr 23, 2009

BCAS1298
  • 3092 Answers

SOURCE: Rear axle oil seals leaking, book shows to remove

TAKE TIRES OFF, REMOVE DIFF. COVER, ON 3rd MEMBER THERE A PIN ABOUT 11/2" DIA. THAT GOSE RIGHT THOUGH THE 3rd MEMBER CLOSE TO ONE OF THE ENDS OF THAT PIN OPOSIT OF RING GEAR THERES AN 8mm SMALL HEAD BOLT ( TURN RING GEAR TO CHECK OTHER END OF PIN ) REMOVE BOLT PUSH AXLE IN REMOVE HORSE SHOES CLIP IN 3rd MEMBER SLIDE AXLE OUT.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999. How can I replace front diff seal?


on the actual front diffr, pinion or the front transfer case seal
the front seal is like the rear.
its a crush cage.
that means when you remove the pinion yoke/flange big bolt
the crash cage is destroyed. also wrecking pinion gear to ring gear back lash..oops.. big big mess-up there...$$$$$$
and such cage must be replaced.
questions????????????
how can you be sure its leaking, when the engine this old loves leak oil

i bet that oil on the ground does not small at all like the nasty stink of hypoid GL5 gear lube. I BET

why not post how to find leaks first
and not do $1000 damage

no engine size posted G16? J20?>
The G16, ill demonstrate (coin toss)
Distributor 2 , o-rings leak like made, all do this old !!!!
same with the 60k mile service and valve cover gasket
all leak, for that reason alone, on all 1990s era
next is cam seal
crank seal
pan seal (or pan is rusted thru as many see (today)
oil pump seal
and gawd forbid the rear main seal , engine.


easy peasy japanezzy

why not ask your mechanic to sniff that oil first and save a fortune
guessing.
!!!!

see man pulling axle to remove pan
wana do that?
http://www.fixkick.com/axles/Pan-drop/pandrop.html

to replace this seal, remove the carrier first
then take it to a shop that can rework the carrier
the correct way.

Jan 25, 2016 | Geo Tracker Cars & Trucks

1 Answer

How to remove rear diff from ve commodore?


loosen rear wheels, jack up rear so wheels are free, fit safety stands , drain oil, remove wheels, remove 4 bolts holding axle bearings. remove both axles, remove bolts from tail shaft at diff pinion flange , leave tail shaft in transmission housing or oil will leak out, remove bolts from diff housing, the diff center can now be removed.

Aug 28, 2014 | 1998 Holden VT Commodore

1 Answer

How to replace pinion bearing 99 dodge ram


If its a 4x4 remove rear drive shaft from vehicle, remove large nut (pinion nut) at front of diff which is generally hidden when driveshaft is in place. with a bearing puller remove pinion bearing replace with new one, install new pinion seal reinstall pinion cover and pinion nut tighten to specified torgue reinstall driveshaft check diff oil for proper amount

May 31, 2014 | 1999 Dodge Ram

1 Answer

Jeep cherokee rear differential


diff overheating is from incorrect mesh of the crownwheel and pinion
that can be from too little clearance , too much clearance of failing bearings and too much preload on the pinion bearings
it can also be from incorrect oil level in the diff to the bottom of the threads of the fill plug
it is time to pull the diff and check the bearings
the problem will most likely be the bearing behind the pinion as that one takes all the load
diffs normally run hot but it is the escaping oil that is the problem
that could be from bearings on the pinion allowing the lip of the flange seal to not seal properly

Feb 28, 2017 | Cars & Trucks

3 Answers

1984 Toyota pickup leaking fluid where the drive line connects to the differential. Bought the rear seal. What is involved in replacing it.


tearing the rear-end apart, replacing that seal, you might as well have new bearings put in as well!
Also this is a more "advanced" repair, having to use plastigauge(or equivalent) to get your clearences EXACT!!!
Good luck

Jan 22, 2011 | 1984 Toyota Pickup Deluxe

1 Answer

Leak at rear diff (pinion seal?) 03 4X4 ford ranger


the part is called the pinion flange seal, pull the drive shaft, remove the large nut on the flange the drive shaft connects to and remove the flange, then pry out the old seal and lube the lip of the new seal with motor oil and press it into the opening. The 7.5 hour estimate is way wrong, about 1.5 hours labor and $4 for the part.

Apr 23, 2009 | 2002 Ford Ranger Regular Cab

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

2 Answers

Rear diff leak on yoke of 2000 explorer


To replace the seal you must pull out the carrier assembly and the pinion gear and install a new crush sleeve if you do it by the book, I have found that if the yoke is removed a new seal installed and the yoke tightened to about 50 foot lbs of torque it is ok, as far as the lube goes there is a plug on the cast case of the diff, it will either be a square drive plug or a large allen plug, fill the diff so you can just touch the fluid with your little finger, don't overfill or the axle seals will start leaking.

Nov 29, 2008 | 2000 Ford Explorer

1 Answer

Pinion seal leaking


check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Oct 22, 2008 | 2004 Ford F250

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...