Question about Cars & Trucks

1 Answer

I'm after a brake diagram for a 1990 Toyota seca I

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,734 Answers

If you haven't touched the other side then it will be the image of the undone side. Just take off the drum and reassemble the first side as it appears on the untouched side.

Posted on Jul 15, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding 02 toyota sequoia


You have a helper pushing on the brake pedal when you open the bleeders? Is fluid coming out of the bleeders when you open them?

typically you will start at the right rear, then left rear, then right front, then left front. or work your way from the farthest bleeder to the nearest bleeder to the master cylinder. Make sure the reservoir does not go dry or you will have to start over.

It is possible that when you pushed the pedal to the floor the seals in the master when through some debris and where ruined.

Apr 11, 2013 | 2002 Toyota Sequoia

1 Answer

Where is the brake master cylinder in a 1990 toyota camry


The brake fluid master cylinder is attached underneath the break fluid reservoir which is where you put brake fluid into. The master cylinder system goes directly into the brake booster which mounts in the fire wall on the driver side.

Oct 08, 2011 | 1990 Toyota Camry

1 Answer

Brake warning light is on, emergency brake is ok. Is brake cylinder at back of engine on driver side? Do I just add brake fluid to the fill line? Is there a particular kind of brake fluid to use?


If the fluid is lower use dot3 brake fluid.There is a sensor in the master cylinder for the level.If the light goes off then have your brakes checked out if your pads are low the the calipers will be moved out when this happens the fluid level will drop if the calipers are push back in after brake pads are installed the fluid level will go back up i hopes this helps :)

Jan 31, 2010 | 1990 Toyota Pickup

2 Answers

How do you take the front caliper off a 1990 toyota camry? i undid the 2 bolts on it, now do i just pull or what?


You can sometime just pull it off but sometimes you will need to take a screwdriver and push the brake pad back on the caliber piston side. This will force the piston back and allow you to remove the caliber. After you remove it you will need to compress the caliber piston fully back in order to allow room the install the new pads and get them back on the rotor. Sometimes you can fully compress it while the caliber is still installed. On some vehicles like Honda you need a special tool in order to compress the caliber. Most auto parts stores will lend you the tool if you buy the pads from them. Be sure and loosen the master cylinder fill cap to allow the brake fluid to expand in the master cylinder. Clean everything off with spray brake cleaner before installing the new pads and clean the new pads throughly. Be sure and install pads in pairs. Do both front wheels or both back wheels not just one.

Dec 03, 2009 | 1990 Toyota Camry

2 Answers

Brake pedal does not work, the brake fluid is


The system has air in it and will have to be bled out.

Nov 08, 2009 | 1990 Toyota Celica

2 Answers

Emergency brake light stays on, weather brake is pulled or not. toyota 1990 pickup 4x4. any guesses?


did you check the float inside the master cylinder reservoir or check the limit switch for the e-brake lever to make sure it is making full contact?

Jul 15, 2009 | 1997 Toyota Tacoma

1 Answer

Replace front brake pad 2003 toyota 4 runner


Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Mar 19, 2009 | 2003 Toyota 4Runner

2 Answers

1990 4Runner bakes are soft


soft(low) brake pedal has 5 possible cause
1 air in system
2master cylinder bypass
3fluid leak
4rear brake shoes out of adjusmet(too far from drum)
5spongy brake pads
if there is no leak and the fluid is at level I would adjust rear brakes and bleed system.If that did not work replace master cylinder.

Jan 20, 2009 | 1990 Toyota 4Runner

1 Answer

Front Rotoe removal 1990 Toyota 3Runner


Take off the disk pad, release the pressure.
1. Loss the brake fluid small fitting on the cylinder, then use one hand slowly loss the fitting and use another hand with flat screw driver pressure the brake pad toward the piston of the cylinder AT THE SAME TIME , as soon as you release the pad a little bit, close the fitting right away, DO NOT LET THE AIR GET INTO YOUR BRAKE LINE. After you release the pad, TIGHT the fitting.

2. Take off two screws behind the cylinder which connected to the body and remove the cylinder first and then take off the rotor.

3. When you put back, don’t touch the fitting, after you finish it, check everything is O.K. then start the car, pump the brake several times, until you feel the brake is normal.


For your safety, use emergency brake and also put something behind your rear wheel to completely stable the car.

Good luck, hope this can help you.
Frank

May 24, 2008 | 1990 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...