Question about Cars & Trucks

Open Question

Wohlenberg 38fs30 infeed fault error 19

Showing infeed engaged need to know how to disengage the sensor

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cruise button works & it lets me set it. Without braking, it disengages. The "possible fix" was to get a new brake light switch. It didn't fix my problem. Anybody have an ideas?? Thx. Mel


cruise controls need fully functional units to stay engaged
they include
brake sensor ,
clutch sensor ,
VSS ,
tachometer
cruise switch
if any one has a problem it will disengage
also it only works above a certain road speed or engine rpms

Apr 23, 2017 | Cars & Trucks

1 Answer

Cruise control notworking on a 2002 F150


cruise controls are controlled by the following switches and sensors
1 the switch itself
2-- the clutch pedal sensor or the VSS in the auto transmission
3 the brake sensor ---4-- the gear change switch or selector
5-- the engine speed sensor ( tacho)
6-- the road speed (VSS )
if 1 or a combination is not working or is outside parameters , the cruise control will not switch on
the road speed in a manual is set at around 20 mph and any less will not engage cruise control(CC)
changing gears in a manual will disengage CC
touching the clutch pedal will not allow engagement or will disengage CC
for some sensors run the fault codes

Nov 05, 2015 | 2002 Ford F150 Regular Cab

1 Answer

Warning light


It sounds like you have a bad sensor, indicating the brake is engaged when it's not. Have you noticed if it tends to display the error when you go over bumps or turn sharply?

Aug 20, 2013 | 2002 Audi A4

1 Answer

4x4 stays engaged adn light stays on what do i need to do?


is it an auto trnsfercase ? if so try hiting sensor with a screw driver and see what happens but probable going to need a new sensor

Dec 14, 2012 | 1997 Jeep Grand Cherokee

1 Answer

Cant Find a list of codes 1989 Buick Century. Car stalls and has a rough idle. coads are 31 43 and 44


Here is a code list for you. Remember this doesn't always mena a sensor issue, the problem can be in the wiring as well, or in the case of a lean code you may have an actual lean condition due to a vacuum leak at the intake or vacuum hoses or connections. I have highlighted your fault codes and added extra notes.
GM common codes for OBD1 (for vehicles made before 1995)
12 System normal
13 oxygen sensor circuit open
14 coolant sensor high resistance or shorted
15 coolant sensor circuit low or open
16 direct ignition system (DIS) fault in circuit
17 cam position sensor fault
18 crank or cam sensor error
19 crank sensor circuit fault
21 tps sensor out of range
22 tps sensor signal voltage low
23 intake air temp sensor out of range, low
24 vehicle speed (vss) sensor circuit fault
25 air temp sensor sensor out of range, high
26 quad-driver module (computer) circuit #1 fault
27 quad-driver module (computer) 2nd gear circuit
28 quad-driver module (computer) circuit #2 fault
29 quad driver module (computer) 4th gear circuit
31 camshaft position sensor fault
32 egr circuit fault
33 map sensor signal out of range, high
34 map sensor signal out of range, low
35 idle air control sensor circuit fault
36 ignition system circuit error
38 brake input circuit fault
39 clutch input circuit fault
41 cam sensor circuit fault, igntion control circuit fault
42 electronic spark timing (EST) circuit grounded
43 knock sensor malfunction or electronic spark control (ESC) circuit fault (ignore this for now)
44 oxygen sensor lean exhaust (make sure you no engine vacuum leaks)

45 oxygen sensor rich exhaust
46 pass-key II circuit or ps.pressure switch circuit fault
47 pcm-bcm data circuit
48 misfire diagnosis
51 calibration error, mem-cal, ecm or eeprom failure
52 engine oil temperature circuit, low temperature indicated
53 battery voltage error or egr or pass-key II circuit
54 egr system failure or fuel pump circuit low voltage
55 a/d converter error or pcm not grounded or lean fuel or frounded reference voltage
56 quad-driver module #2 circuit
57 boost control problem
58 vehicle anti-theft system fuel enable circuit
61 a/c system performance or degraded oxygen sensor signal
62 engine oil temperature high temperature indicated
63 oxygen sensor right side circuit open or map sensor out of range
64 oxygen sensor right side lean exhaust indicated
65 oxygen sensor right side rich exhaust indicated
66 a/c pressure sensor circuit low pressure
67 a/c pressure sensor circuit or a/c clutch circuit failure
68 a/c compressor relay circuit failure
69 a/c clutch circuit head pressure high
70 a/c refrigerant pressure circuit high
71 a/c evaporator temperature sensor circuit low
72 gear selector switch circuit
73 a/c evaporator temperature circuit high
75 digital egr #1 solenoid error
76 digital egr #2 solenoid error
77 digital egr #3 solenoid error
79 vehicle speed sensor (vss) circuit signal high
80 vehicle speed sensor (vss) circuit signal low
81 brake input circuit fault
82 ignition control (IC) 3X signal error
85 prom error
86 analog/digital ecm error
87 eeprom error
99 power management

Jul 21, 2011 | 1989 Buick Century

1 Answer

When i pull the code up on my 1992 park avenue it blinks once then blinks twice. what does this code mean?


This is code 12 and it means "System Normal"
Here is the complete list of fault codes for your Buick
GM common codes for OBD1 (for vehicles made before 1995)
12 System normal
13 oxygen sensor circuit open
14 coolant sensor high resistance or shorted
15 coolant sensor circuit low or open
16 direct ignition system (DIS) fault in circuit
17 cam position sensor fault
18 crank or cam sensor error
19 crank sensor circuit fault
21 tps sensor out of range
22 tps sensor signal voltage low
23 intake air temp sensor out of range, low
24 vehicle speed (vss) sensor circuit fault
25 air temp sensor sensor out of range, high
26 quad-driver module (computer) circuit #1 fault
27 quad-driver module (computer) 2nd gear circuit
28 quad-driver module (computer) circuit #2 fault
29 quad driver module (computer) 4th gear circuit
31 cam position sensor fault
32 egr circuit fault
33 map sensor signal out of range, high
34 map sensor signal out of range, low
35 idle air control sensor circuit fault
36 ignition system circuit error
38 brake input circuit fault
39 clutch input circuit fault
41 cam sensor circuit fault, igntion control circuit fault
42 electronic spark timing (EST) circuit grounded
43 knock sensor
or electronic spark control circuit fault
44 oxygen sensor lean exhaust
45 oxygen sensor rich exhaust
46 pass-key II circuit or ps.pressure switch circuit fault
47 pcm-bcm data circuit
48 misfire diagnosis
51 calibration error, mem-cal, ecm or eeprom failure
52 engine oil temperature circuit, low temperature indicated
53 battery voltage error or egr or pass-key II circuit
54 egr system failure or fuel pump circuit low voltage
55 a/d converter error or pcm not grounded or lean fuel or frounded reference voltage
56 quad-driver module #2 circuit
57 boost control problem
58 vehicle anti-theft system fuel enable circuit
61 a/c system performance or degraded oxygen sensor signal
62 engine oil temperature high temperature indicated
63 oxygen sensor right side circuit open or map sensor out of range
64 oxygen sensor right side lean exhaust indicated
65 oxygen sensor right side rich exhaust indicated
66 a/c pressure sensor circuit low pressure
67 a/c pressure sensor circuit or a/c clutch circuit failure
68 a/c compressor relay circuit failure
69 a/c clutch circuit head pressure high
70 a/c refrigerant pressure circuit high
71 a/c evaporator temperature sensor circuit low
72 gear selector switch circuit
73 a/c evaporator temperature circuit high
75 digital egr #1 solenoid error
76 digital egr #2 solenoid error
77 digital egr #3 solenoid error
79 vehicle speed sensor (vss) circuit signal high
80 vehicle speed sensor (vss) circuit signal low
81 brake input circuit fault
82 ignition control (IC) 3X signal error
85 prom error
86 analog/digital ecm error
87 eeprom error
99 power management

May 05, 2011 | Buick Park Avenue Cars & Trucks

1 Answer

The 4WD! Warning Light keeps coming on then turns off, Electronic Stability Program (ESP) light is on sometimes and not others and the Traction Control System (TCS) Indicator Light. the first time they...


TCS And 4wd use the abs wheel sensors to engage and disengage so if there is a slight fault in the abs sensor system TCS will be disabled and the 4wd will either not engage or disengage depending on the drive position set at time of fault that is what the lights are telling you
Get the sensor system checked out from the abs rings on the axles to the sensors and wiring to the abs pump controller

Sep 05, 2017 | 2008 Jeep Compass

1 Answer

I'm getting this code p0582 on Mar 19 2009 you sad you did not no what it was. Do you know now? there no more codes. Cruise Control Related Malfunction i tern on the Cruise Control. Light comes on I set...


P0582 is the Chrysler Diagnostic Trouble Code (Error Code) for:

Speed control vacuum or vent solenoid circuits open or shorted

If you do not have cruise control on your vehicle, you can ignore this code. If you do, you've probably noticed it is no longer working or only works intermittently. The code is saying it's an electrical problem to the servo.

Jun 24, 2010 | 2002 Dodge Intrepid

3 Answers

I need to know what the code 18 and 41 means for 93 Buick Park Avenue Ultra with a 3.8 litre supercharged eng


When fixing codes start with first code first / it dos not always mean that the sensor is the fault ,it could be in the harness / the plug or the ground. and reference signal should be tested , but in this case you most likely could get away with replacing the cam sensor, that would be the Lest expensive and easiest to start with,to git to it you will have to remove the alternator hope this is help full, the other code suggest that it could be the crank sensor , that and the plug for it does fail quite often but first things first feel free to ask if you should have any further questions , Thank you ,

Mar 31, 2010 | 1993 Buick Park Avenue

1 Answer

4x4 indicator light flashing


Drivetrain -
4WD Lamp Flashing/DTC33 Set 02-23-007- TSB #
11/01/2002- TSB Date

I found the TSB and Title but unfortunately it will not allow me to access it for some reason. This might give you something to show them when you talk to them again. Hope this helps!

Lefty64

Apr 08, 2009 | 2001 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...