Question about Cars & Trucks

Open Question

#3 cylinder misfire 2006 chrysler sebring 2.4L 4 cylinder

Replaced coil pack, plugs, plug wires

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: engine code p0307 cylinder #7 misfire

It could be carbon deposits on valve seats keeping valves from totally closing. You can try getting you a can of motorcraft PM3 top end engine cleaner and get engine up to operating temp then remove one of the small vacuum lines from the intake and draw the contents of the can slowly into the engine.After you have drawn in the contents shut engine off and let it soak for about 45 minutes then crank it back up and let it run until it clears. Now it will smoke like a forrest fire while you are doing this so don't be alarmed,just tell the neighbors you are spraying for mosqitos.This may cure the problem. If not you may be looking at a valve job.
This can be verified with a compression test if this is what is causing it.

Posted on Feb 05, 2009

Ad
  • 1 Answer

SOURCE: 99 cougar v6 P0352 misfire cylinder 3 and 4 replaced igntn coil..

Had the same problem, car was misfiring on cylinder 3 and 4. replaced wires, plugs, and ignition coil. still misfired on the same cynlinders. turned out the main engine wiring harness plug in was coming loose. spent well over $150 on the unneccesary repairs and ultimately fixed the problem wit a $3 bag of wire ties to hold the plug in...

Posted on Jun 01, 2009

  • 5 Answers

SOURCE: 2003 Chevy Venture misfiring

The injector is a good possibility, although you should check for spark in the wire first, as the electrical is the weakest link in the system. Put a spare plug in the end of the wire with the plug resting on metal, then have someone crank the van to see if you have spark that far, test and replace spark plug, (do not get shocked!) then look into a new injector or a good cleaning.

Posted on Jul 17, 2009

  • 119 Answers

SOURCE: MISFIRING ON CYLINDER 1 VW POLO 1.4 3CYLINDER

I have changed a few cylinder heads under warranty for this type of problem. The exhaust valve guides wear, this causes the exhaust valve to seat badly, giving low compression. if one cylinder compresion reading is more than about 50 psi below the others, then this warrants head removal. It is quite a job, due to the fact that the camshft id chain driven. If you are up for it then once the head is removed, poor liquid into the exhaust ports and see if it leaks out through any of the exhaust valves.

Posted on Jul 23, 2009

  • 110 Answers

SOURCE: i have a 99 grand am SE 2.4 4 cylinder and my

A misfire doesn't always have to be ignition... it's just the most common cause. Faulty or plugged injector, low compression. You need to check fuel pressure and test the fuel injector flow. Then check compression. If you don't have tools for these tests, take it to someone who does. Testing is much cheaper than throwing parts at the problem.

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0303 cylinder 3 misfire in 2008 Chrysler sebring convertible, changed all spark plugs & coil pack. Engine light continues to come on with this code ?


Recheck all work you have done. Sometimes folks replace the wrong coil pack as they can be easily confusing. If everything seems ok, there are still two possibilities. First, ensure that the fuel injector is consistently firing for the cylinder, and also ensure that it is not constantly firing. Either can cause a misfire, one for too little fuel, one for too much fuel. Lastly, check compression in the suspect cylinder. A broken or burnt valve can cause loss of compression, leading to misfires.

Aug 10, 2016 | 2008 Chrysler Sebring Convertible

2 Answers

2009 chrysler sebring changed spark plugs cause it said number 3 was misfireing them put in a new thermostat in it started up but then started back not wanting to crank it acts like its flooding


were you sure to set the gap on the plugs? and replace them with the correct plug for that matter? also...why was the thermostat replaced?

Sep 10, 2015 | Chrysler Cars & Trucks

1 Answer

Replace coil packs on the ford explorer 2006


What codes P0304 & P0308 ? This just means the PCM detected a misfire on those cylinders .an could be a few different things !
What ignition type does your vehicle have coil on plug or a coil pack with 8 plug wire towers ? If you have coil on plug ignition there are two wires going to the coils , one has battery + an the other is control from PCM . Check power first with volt meter or test light . Or use a spark tester on those two cylinders . No Spark Testing control testing

Feb 24, 2015 | 2006 Ford Explorer Eddie Bauer 4x4

2 Answers

Have a 2002 chrysler town and country, stumbles and back fires, have a code p0302


#2 cylinder misfire. Plug, wire, or coil pack. One of them is bad. My guess is the coil pack. Pull the wire off the coil, lay it on top the coil close to the #2 port. Start the van. You should see the coil throwing an arc to the plug wire. No arc replace the coil. If you have arc, then replace the plug and wire. I would do all of them.

Feb 14, 2015 | Chrysler Cars & Trucks

1 Answer

I have a sebring 2004 v6 2.7 which is misfiring. put it a new coil and changed plug on cylinder that doesnt fire still no spark. im getting power all th way to the plug tested with volt meter.it reads 14...


Invalid test. When plug fires, the wire shoots around 40,000volts. When not firing, there is no current in the wire.
Try switching the misfiring plug wire with another that is firing. Switch them both at the plug and at the coil tower. If that was a bad plug wire, the misfire will now be on the cylinder where you put the suspect wire. This will confirm a bad plugwire.
Good luck.

Nov 25, 2011 | 2004 Chrysler Sebring

2 Answers

I have a 2001 toyota fourrunner showing computer codes p-0300 & p-0304. What are these codes for?


The P0300 is a random multiple misfire code, the P0304 is specific to the number 4 cylinder, a common problem for this code is a igniter/coil malfunction on the #4 cylinder, each cylinder has it's own coil, what you can do is to remove the #4 coil pack(it's the middle one on the driver's side) and switch it with coil #2 which is the first one on the driver's side, clear the codes and drive it if the code now shows P0302 replace the coil.

Aug 21, 2011 | 2002 Toyota Sienna

2 Answers

87 Mirage Misfiring


could be a bad plug or a bad coil or even an injector

Jan 26, 2010 | 2006 Chrysler Sebring

1 Answer

Coil pack


On all four cylinder sit on top of engine toward back, follow spark plug wire from top of valve cove to coil pack. On six cylinder engine the ignition coil sit inside the distributor under the cap where the spark plug wires go.

Jan 06, 2010 | 1998 Chrysler Sebring

2 Answers

Loation of spark plugs on 2006 chrysler sebring


They go into the cylinders through the middle of the valve cover.

Jul 28, 2009 | 2006 Chrysler Sebring

1 Answer

Multiple cylinder misfire detected


sounds like its time for a coil pack and any connector upgrades chrysler has. have a good day DB

Feb 03, 2009 | 2002 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...