Question about 2004 Pontiac GTO

1 Answer

Slave cylinder location on a 2004 GTO.

I got a project car that has a clutch burnt out. I bought it for my son but he doesn't know it yet. He thinks I am fixing this for a friend. We worked all day replacing the clutch in it but now it has a very soft clutch pedal. I serviced the fluid and pumped it at least 50 time. Disconnected the line underneath and had my son pump the pedal. Very little pressure was felt on my finger. Can u please advise what can be the problem. I suspect the slave cylinder but cant find it.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 12,440 Answers

From the look of ,it should be mounted to the fire wall along side of the brake master cylinder .

Posted on Jun 03, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: Fuel Pump Relay Switch

Underneath your hood, behind the passenger side headlight, behind the core support, is a bank of 2-8 relays. One of those relays is the relay needed for your fuel pump. There will also be a fuel pump relay fuse located there. The relay designation should be on the cover of the relay compartment.

Posted on Jan 03, 2009

  • 21 Answers

SOURCE: 1989 Pontiac 6000 LE

Check AutoZone.com as they have an area where they can tell you where the parts are located on your car.

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

  • 2187 Answers

SOURCE: clutch adjustment

Its either the clutch fluid is wrong or not at the correct levels or it has not been bled correctly.

Posted on Nov 30, 2009

  • 1 Answer

SOURCE: I have air in my power steering lines and cant get it out?

i have a 97 ponitac grand prix gt and i was fixing a loose connection and on the power steering and now i can't get the air out of the lines and it's been almost 3 days all the connections are tight and just cant seem to get the power steering to work at all when i lower the wheels back the ground.

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Kia Spectra5 hatchback......wondering if the master/slave cylinders are located inside the transmission or ouside? My mechanic can't tell me without looking at the car...?


So we are talking manual transmission clutch operation here?

Your master cylinder is located on the firewall, on the other side of the clutch pedal. Your slave cylinder is located next to the gearbox bell housing.

The slave cylinder:
11_6_2012_11_53_26_pm.jpg

The master cylinder:


11_6_2012_11_54_27_pm.jpg

Nov 06, 2012 | Cars & Trucks

1 Answer

Hyundai Elantra clutch Pedal Stuck Up


The axle job should not have caused any problem to develop in the clutch.
I don't see how they could have.
If you can work the slave by hand, it may be a problem with the clutch master cylinder. Maybe the rod from clutch pedal into the master is bent or binding up and won't travel into the master. You could check if master operates easily by taking line off at the slave cylinder (or if not able to remove hose, then open the bleeder valve on slave) and see if your pedal operates now. Use a can to catch fluid if you don't want it to spill on floor. If the pedal still won't move it must be a problem with the master cylinder or the clutch rod.
If the pedal works with line removed, or the bleed valve open, then the release bearing inside the bellhousing must be binding up and not moving forward to engage clutch. (The slave cylinder pushes the clutch fork lever which pushes the release bearing forward on a shaft up against the clutch pressure plate to allow the clutch to operate .If the release bearing is the problem, the transaxle will have to be removed to fix it.
As I said, though, if you can operate the slave and the cllutch lever it pushes with your hand, it doesn't sound like it is binding down there. Check the pedal's push rod going into the master cylinder. Good luck.

Jun 01, 2012 | 2001 Hyundai Elantra

1 Answer

Transmission issues


Typical Clutch Problem. Check to see if Clutch Linkage is Hydraulic or Mechanical. If Hydraulic then replace Clutch Slave Cylinder First.Bleed out air from Hydraulic line. if this doesn't fix it and or it has a Mechanical Clutch Linkage then Replace Clutch itself don't forget to get a new throw ou bearing and pack it with heavy duty grease otherwise in 20,000 miles you'll be doing it again. Thanks Keith

May 15, 2012 | 2004 Pontiac Sunfire

4 Answers

My clutch pedal is sticking to the floor?


Hi replace the clutch cylender

Nov 22, 2017 | Cars & Trucks

1 Answer

Holden rodeo ran out of clutch fluid, bled it through and will not disengage, when running and try to move theres a slight pressure loss feeling and will not move.


No leaking? I don't know, but possibly your clutch master cylinder may be failing with an internal leak that doesn't allow pressure to build up at the slave cylinder. Or maybe the slave cylinder itself is bad.
Good luck.

Feb 09, 2012 | Suzuki Sidekick Cars & Trucks

1 Answer

My problem is that the manual transmission is stuck in 4th gear. I was backing up when I went to put it into 1st the shifter was stuck. The clutch works to disengage the gears but the shifter won't...


That cylinder is known as the clutch slave cylinder. It should push against the clutch fork every time the clutch pedal is depressed to allow gear changes. If it doesn't, suspect a faulty slave cylinder, or clutch master cylinder.

Sep 09, 2011 | 1999 Nissan Sentra

2 Answers

I have a 91 passat and the clutch pedal stays on the floor. I bought this car as a project. It has been sitting for 5 years w/ a busted timing belt. Timing is fixed and is running but the clutch pedal just...


If you're talking about an hydraulic clutch system that uses brake fluid:
1. Fill the reservoir with clean brake fluid.
2. Have an assistantpull the clutch pedal up and leave it there.
3. Locate the slave bleeder - the slave is connected to the master, is located on the transmission housing and pushes the clutch release lever).
4. Open the bleeder and have the assistant push the clutch pedal down.
5. Close the bleeder.
6. Make sure there's plenty of fluid in the reservoir
7. Repeat steps 2-4-5-6 until brake fluid comes out with uniform pressure from the bleeder. Non uniform pressure is sign there may be air in the system.
There should be good pressure at the pedal now in the up position. Pressing it should disengage the clutch.

Aug 23, 2011 | 1991 Volkswagen Passat

1 Answer

I have a 2000 Jeep wrangler and the clutch will not press down at all.


Look to make sure your Hydraulic fluid level is full for the clutch. It is located near the brake master cylinder(see owners manual) . If it is low , fill it and pump the clutch pedal a few times and see if that takes care of it. If it doesn't then I would be looking at replacing the slave cylinder and master slave cylinder for the clutch. If it is completely empty and you fill it and pump it a few times, and its back to empty. Yes, you guessed it, look for a leak.

Jan 14, 2011 | 1995 Jeep Wrangler

2 Answers

2004 cavalier clutch pedal stays on floor,clutch not slipping. do i change clutch master cyl


Check for fluid leaks first along the line. Also check the mechanical linkage. Then try bleeding it. Changing the master cylinder is your last resort. That way you dont buy parts you don't need.

Nov 14, 2009 | 2004 Chevrolet Cavalier

Not finding what you are looking for?
2004 Pontiac GTO Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...