Question about Nissan XTrail

Open Question

Remove cup holder - XTrail Nissan Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

egstriker23
  • 44 Answers

SOURCE: Replacing the broken cup holder

First, you must remove the floor console bezel (the trim piece that surrounds the shifter knob). The proper method to remove this involves removing the shifter knob first. This is held in by a small set screw on the "radio" side of the knob. To remove the screw, you will need a small "hex-key" (also known as Allen key or Allen wrench). The proper size is 3mm, but you can get away with using a size 7/64" if you need to. Once loosened, I believe that the knob pulls right up and off. Make sure you do not lose the small screw. Also be careful not to accidentally contact the tip-top of the shifter while the knob is removed, as this may break off the small black plastic tip, which will require much more work to repair and/or replace the entire shifter.
Next, you should be able to remove the floor console bezel by prying gently and carefully on the corners and sides of the piece with a tool called a trim stick, or if you do not have this tool, you can get away with using a small, thin-tipped flat head screwdriver. However, this will almost surely cause some aesthetic damage to the edges of the trim.
Once this bezel is out of the way, (you shouldn't have to remove the electrical connectors on the underside of the bezel for this specific job) there are 2 screws holding down the bottom of the cupholder assembly. I believe these are both Torx - type screws, which will need either a T10, T15, or T20 screwdriver bit to remove(I'm sorry but I don't remember exactly which of the 3 sizes are used). After these 2 screws are removed, open the armrest. On the TOP of the FRONT of the armrest, just above the cupholders, are 2 more screws which should be the same as the 2 bottom screws. Remove these, then lift the cupholder assembly up and forward to remove it.

To install, simply reverse the above procedure.

Because this is my first solution posted on this site, I would love to have your feedback. Please let me know how everything goes with this project. Thank you!

Mitchell

Posted on May 27, 2009

Auto Master
  • 139 Answers

SOURCE: I need to get under the cup holder section of the console

Hello,
I hate to be the berrer of bad news but unless you can sneek a grab at it from the side you will need to remove the whole console. I would try some of those 4 jaw flexible pincher grabbers most parts stores would cary them.

Roy

Posted on Nov 16, 2009

  • 95 Answers

SOURCE: broken cup holder in 2000 BMW 740iL

http://www.bimmerboard.com/forums/posts/308465

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The cupholder in my Montana is stuck,and won't come out...what do I take apart to get it back out?


Dash Cup Holder is stuck and won't come out, how do I fix ...

www.fixya.com/.../t10005627-dash_cup_holder_stuck_won_39_t_come
Aug 5, 2011 - Dash Cup Holder is stuck and won't come out, how do I fix it? - Saab 2004 9-3 ... How do I remove an in-dash cup holder in my 2005 Chevy Malibu. Apr 26, 2014 ' 2005 ... Nov 05, 2012 ' 1999 Pontiac Montana ยท 1 Answer ...

cup holder montana van Questions & An


Dec 26, 2015 | Cars & Trucks

1 Answer

How do I remove an in-dash cup holder in my 2005 Chevy Malibu


open the cup holder and under side of holder is a tag that needs to be pushed down whilst pulling gently on the cup holder , if the tag is not under neath it will be towards the dash end of the cup hole , depends on the part supplied at time of manufacture

Apr 26, 2014 | 2005 Chevrolet Malibu

1 Answer

Replacing cup holder


I assume you mean the one that flips up in the center console?

If so, there are three likely issues.

1) did you slide out the retainer from the upper screw? the top screw had a cover that had to be pried off. you then took the screw out. Lastly you have to slide out the plastic retainer that the screw went into. It slides out towards the opening.

2) you have to have the cup holder partially open to remove it. the hinged part that folds up is stored in the cavity under the console when closed. you have to open the cup holder and keep pushing until the front of the cup holder lip comes up. Work the cup holder up and down until it comes out.

3) the cup holder is stuck in place due to years of spilled liquid. If you've done the above, then you can either spray soapy water on the creases around the opening and let it set, or you can apply strategic brute force.
Be aware through. if this is the center console cup holder just behind the gear shifter. There are two screws and nothing else to hold it in. Just be carefull....

Mar 17, 2014 | Volvo S80 Cars & Trucks

1 Answer

1999 subaru outback cup holder stuck


the only way to fix this is the hard way.
you need to remove the pop out trim the holds the dash cup holder
carefully pry the edges around the trim to remove it
once its out you can unscrew the cup holder then try to see why its no longer working

Dec 15, 2013 | Subaru Cars & Trucks

1 Answer

Want to remove console to replace cup holder on 05 crossfire.how do you remove hand brake handle?


right above the cup holder is a cover the length of the cup holder remove it pops out.
2 screws hold the cup holder 2 hold the bezel u only need to take the 2 for the bezel out. The rest will pop off and disconnect the connectors for the AC and so on.

Mar 03, 2011 | 2007 Chrysler Crossfire Convertible

1 Answer

I have an '08 TL with a very annoying object sliding back and forth when I brake and accelerate. Sounds like it is under the cup holder. I removed the trim on both sides. That is where I am stumped. Is...


the center console will prob. have to be removed , there are hiden screws, be patiant and thuroly look before just ripping out cup holder.

Feb 11, 2011 | 2008 Acura Tl

1 Answer

Rear cup holder broken, how do I replace it?


normally cup holders are bolted or fastened by a screw to its base, remove the screw and lift up the broken cup holder and install a new one...

Apr 07, 2010 | 1997 Mercury Mountaineer

2 Answers

Broken cup holder in 2000 BMW 740iL


unfortuantly the whol center councle needs taken apart it is harder than it looks sorry for the bad news, an easy fix is to just replace the front part of the cup holder

Mar 24, 2009 | 2000 BMW Z8

1 Answer

2000 Honda Odyssey Coin Holder


open the cup holder shine a light above it you will see a tab you can use a screwdriver to seperate the tabs and the cup holder will slide out

Sep 04, 2008 | 2000 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...