Question about Cars & Trucks

Open Question

Geo tracker drl module - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: HOW DO YOU REMOVE THE RADIO FROM A 1995 GEO TRACKER????????

To remove the radio:
Remove the ashtray by raising the armrest cover and removing the two screws at the rear of the ashtray. Slide the ashtray back and then lift it out. Be careful of the two front tabs, as you don't want to break them.
Reach below the wood console, where the ashtray front tabs were inserted. Loosen and remove the two wing nuts.
With a small, long flat bladed screwdriver, pry out the leather shifter surround. The leather shifter surround has a center chrome retaining ring, the leather surround, and then finally a black plastic surround. The chrome retaining ring has 3-4 tabs which are locked in below the leather surround. It depends on the year of the Jaguar. Probably the 95 has three, but maybe four. They should be at the front and rear of the trim piece (2 front and 1 back, or 2 front and two back) but I've seen then on the sides. The point is, you have to be careful with the screwdriver and find the tabs. The screwdriver should be slid between the leather and the retainer. Pull upwards on the retainer gently, and as you loosen the tabs, it will come out.
Remove the leather surround. Once the chrome retainer has been removed, it should be easy to work it out of the console.
Loosen the black trim ring gently as it has tabs as well, but they are visible once the leather trim has been removed. Lift it upwards out of the wood trim and pull it to the side out of the way. You don't need to disconnect the wires, just lay the black trim to the side.
Lift the rear of the wood console trim and gently, gently slide it back and up. It will try to hang on the leather console, and can be difficult. Patience is important, as the walnut on the ski slope cracks easy (really easy).
Once the wood console trim (ski slope) is removed, you should have a row of screws up the side of the center control panel, where the radio and AC controls are. There are four to six on each side, depending on what Jaguar used at the time, as the 95 cars mechanically are somewhat of a blend of the XJ40 and the XJ300. Remove these screws, and note any spacers that were behind them. These spacers get lost quickly, and cause the ski slope to sit awkwardly on the console.
The radio will slide forwards once these screws are removed. Remove the radio harness and the antenna lead. As the books say, assembly is reverse of removal.
Good luck, and let me know if you have questions. If you are replacing the radio, let me know as I have the harness wiring codes and can help you with that as well.

Posted on Jul 01, 2008

  • 14036 Answers

SOURCE: 94 & 95 Geo Tracker obd1 cable

you need the same brand cable.

Posted on Apr 06, 2009

  • 2 Answers

SOURCE: reset check engine light on 1995 geo tracker

I had the very same problem with my 94 tracker and it turned out to be something simple. My check engine light had popped on after it had hit 100,000. I went through all of the suggestions that people had suggested (unplug battery......etc) and still to no avail. Searching the internet, I came across a website called suzukiforum.com and there, this guy was able to help me with my problem. It turned out to be a maintenance switch that kicks on every 50,000 miles. This switch is like a secret that the auto manufactures use to ploy owners of their cars to bring to the dealer and then rack up the dollars in unnecessary "repairs". The switch is located under the dash and can be hidden anywhere. From the assistance of the guy on the forum, he was able to send me photos of this damn switch and possible locations where it may be mounted. I found mine in about 5 minutes, where it was attached to the steering column. It's a tiny switch, that you slide up or down, depending on what position it is in upon finding it. If it's up, then slide it in the down position and visa versa. Once you do this, the check engine light will go off. Make sure you do not have the car running and you can even unhook one of the battery posts, just to make sure you don't hit anything while rooting around under the dash. Good luck!

Posted on Apr 30, 2009

papayogi
  • 7 Answers

SOURCE: 89 geo tracker fuel filter

Passenger side!

Posted on Apr 03, 2010

  • 72 Answers

SOURCE: 1995 4x4 geo tracker front wheel bearings

first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Highbeam lights very dull on 1999 Geo prism? Put new wiring plug(?) Any idea what the problem is? on and change dimmer relay with no luck! Ant


are you in USA.?
are you in Canada with mandatory DRL lighting?
we can not guess that,
DRL car is complex.
DRL has a 20 pin module just for DRL, crazy complex.
the FLASH on DRL grounds the HL directly bypassing DRL relay
so is super important the FLASH test.
There are 2 systems used, the toyota uses hot all time headlights
(via the HL relay and dimmer relay)


I need this?
is it dim on high, yes,
is it dim on low, no.
is it dim , when you push the lever to FLASH.??????
if flash works we know why it fails. see? (paths)
see?
if high beams and FLASH are dim, then DRL relay bad.
(can be other failures., for sure even wires bad)

its just a:
Toyota Corolla. Gen 6 to 8. (in snake skins)
if you have voltmeter this is child's play , really
finding point of voltage drop tells you what is wrong
find a shop with sparks guy? be best or by a meter and learn>?
guessing can take a long long weekend.
is labor time not a matter to you or down time?
ok I pulled up your cars HL schematic.
DRL is super complex
id pull the DRL module and look for burned pins
they love to do that DRL does.
so got DRL
and does FLASH work right>?

Jan 21, 2017 | Geo Cars & Trucks

1 Answer

1996 geo tracker the running lights passenger side is dim The brights the passenger side goes out I unplugged the drivers side and the passenger side goes out Where can i find the ground wire for them


out side lamps dim, parking?
the brights? ah low beam ok, but high beam dead?
sounds to me bad grounds, but my volt meter wins that argument every time,....

unplugged what?
does your car a tracker like mine, have DRL, as DRL has unique headlight (etc) wiring. (daylight running lamps?)
what luck the only free, suzuki fsm book in the world.
your car, posted 100s of times here.
8a-110
see that
http://www.acksfaq.com/trackerfsm.htm

Dec 28, 2015 | Geo Cars & Trucks

1 Answer

Where is the headlight relay located on a 1999 Chevy Tracker?


Headlight relay #1 location? - Suzuki Forums: Suzuki Forum Site

www.suzuki-forums.com/...geo.../34499-headlight-relay-1-location.html

Nov 12, 2009 - 10 posts - ‎2 authors
After testing everything else, the headlight relay #1 is the main suspect. Where ... Geo Tracker .... then walk the red lead from the fuse to HL Headlights stay ON - 2001 Chevy Tracker
10 posts
May 10, 2013
2003 tracker: Fuse & relay locations
10 posts
Jul 18, 2011
Disconnected DRL module from Tracker/Vitara 2002, but ...
10 posts
Oct 1, 2010
Disabling DRL
10 posts
Sep 5, 2009
More results from www.suzuki-forums.com

Interior Fuse Box Location: 1999-2004 Chevrolet Tracker ...

www.carcarekiosk.com/video/...Chevrolet_Tracker_2.../fuse.../replace
The video above shows how to replace blown fuses in the interior fuse box of your 2000Chevrolet Tracker in addition to the fuse panel diagram location.

Painless Headlamp Relay for 1999 - 2002 Chevy T


Dec 17, 2015 | Cars & Trucks

1 Answer

97 geo metro, low beams won't work, high beams work. dlr doesn't work either


DLR, you meant DRL? day light running lamps>?
are you in canada, if yes, that be good to say , yah?
and if so, the wiring is all unique there, as it is on all cars in all countries (laws )
to fix DRL in ANY car you need (unless luck and inspections fail)
is called a SCHEMATIC. with that and any $10 volt meter this job is easy.
so what do we know. we know the 2 fuses are not BLOWN.
we know that DRL runs low beams. and fails
we know that DRL does not run Highs ever. (top clue)
my guess is FLASH works too, and is clue 2.
clue 3, is the HL relay is good, or high beams would be dead except on FLASH.
the first thing to do with DLR failure. is to pull the module
and see the burnt pins, as all Geo/Suz. love to do.... weak parts.
now some DRL rules. the DRL has logic, and if the inputs to it
fail the DRL fails.
the hand brake most work, that is the switch and the brake lamp on the dash must go out, does it?
rule 2. the DRL lamp on the dash does it work>? normally?

the DRL runs lows.
and the DRL has 2 modes, for DRL
DRL , with the dimming resistor active (DRL mode is dim)
DRL , bypassed mode, driver selects Lows.
the DRL logic sees you do that and exits, DRL dim mode for full bright low beams.
that i show it all works.
see this drawing.
ask how to test it more.. its not hard, ask.

here it is.
sorry that fixya add image sux.. truely.

or measure the voltage on all pins (dlr module)
tell me?them.?
and I tell you whats wrong.but look for burned pins first ,hint hint

c71681ea-3413-49bc-9099-db8e9e2943b1.jpg

Oct 17, 2014 | 1997 Geo Metro

1 Answer

Wiring diagram of headlight


easy but are both dead , or dim or stuck in high?
DRL head lamps or not? Canada has those.
Daytime, running lamp option or mandated.
??????
here is ours. (usa , no DRL) the wiring changes by COUNTRY
the most simple system in the world. the TRACK-KICK.

http://www.fixkick.com/power-elect/Head-lights-nonDRL1w.jpg

Aug 16, 2014 | 1994 Geo Tracker

1 Answer

Need diagram for 1995 geo tracker transmission modulator valve hose connection


top rear of intake manifold
but 1995 has 2 engine (not stated)
and this fitting is different on both.

May 01, 2014 | 1995 Geo Tracker

1 Answer

No headlights on dim only work on bright


old post.(day)
low beams, they are.
both low beam lamps.dead but are PARK/tail dead too?. (a key fact needed here to save time finding cause)
there are more that one cause.
but fuses are first, some cars have 2 fuse.
one for highs and lows.
or for left and right.
they do that so at least some lights work and not all go out at once, on a dark rainy night on a country road (or cliff road)
GEO, the car brand GEO is sold mostly in USA and Canada
if in CANADA the law says its DRL lamps.
in canada they have a Drylight Running lamps and laws and have a unique controller for that (DRL module) and can fail and mess up lamps. so GOT DRL>?
on this car the fues box shows, left and right HL
the next question is does it run a relay.
answer,
DRL, the DRL module runs low beams totally so that be first.
and its DRL relay.
non DLR metro, works like this
im reading the online schematics for you, and so could you.
the no-DRL is brutally simple.
the fuse runs the lamps direct, means lamps hot all the time.
the park and head light switch, grounds the low beam wire feed.
no relays , magic , DRL just a simple switch, in the combo switch.
for you or others seaching Metro head lamps.
here is the schemo.
red/wht wire must be 0v on low beams if not switch bad.
if g200 is good, but g200 is used in highs so can NOT BE BAD.
as you can see the switch grounds the HL lines below.
to make the lamps GLOW,

23880969-flsdwf0rx41rbdaez4cmhnol-2-0.jpg good luck to metros

Mar 21, 2014 | 1995 Geo Metro

2 Answers

Headlights and daytime running lights will not work what is the solution


check DDL relay it is attached to backside of ECM holder on left side under dash up high. Look for burnt/melted plug-in on relay

Jan 07, 2014 | 1996 Geo Tracker 2 Door

1 Answer

DRL Control Module location on a 1999 Chevy Tracker


under the instrument panel and to the right of the steering column, it is a small box.

Jul 05, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...