Question about Cars & Trucks

Open Question

Remove front bumper cover for 2004 kia rio - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: repair diagram for 2004 kio rio

my 2004 Kia Rio keeps losing power?

Posted on Aug 16, 2008

  • 726 Answers

SOURCE: changing front brake pads on a kia rio 2004

ok first you have to take the wheel off
then you will see the caliper there'
there are to bolts behind that take them out
then take the caliper off dont undo nothing else
take the old pads out
use a caliper to push the cylinder back (its what pushes the brake in)
put the new brakes in the same way they came off
do the bolts up
then pump the brakes
is the cylinder is to hard to push back you will have to realse the pressure buy undoing the bleeder then you will have to bleed them again (but in this case they should move easy


Posted on Sep 20, 2008

  • 1596 Answers

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Posted on Jan 16, 2009

c17hydro
  • 2984 Answers

SOURCE: Need help replacing front hub

Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:

  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

Posted on May 13, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instrructions on replacing a rear main seal on 2004 kia rio


Oil leaking "in" your valve cover? Where is the oil at/coming from? And, to answar your question, rear main seal is a real job! Requires removing transmission, flex plate/fly wheel! It is the crank shaft seal, on the "rear" of the engine!

Jun 08, 2016 | 2004 Kia Rio

1 Answer

Cam sensor location for a 2004 1.6 4 cyl. Kia Rio


The cam sensor on a 2003 Kia Rio is located on the front, driver's side of the engine, Should be the same on the 2004 ki8a reo's. God-Bless! This is for the 1.6,

May 20, 2015 | 2004 Kia Rio

1 Answer

Where are the front impact sensors located on 2006 Kia Rio


you are looking for the airbag control module it is located between the 2 front seat

Nov 02, 2012 | 2006 Kia Rio

1 Answer

How to remove front bumper


Remove screws in wheel wells holding bumper to inner fender, and fender. Then remove screw holding the splash guard to the lower bumper cover. Finally, remove screws holding the bumper cover to the core support on each side of the grill, and possibly the outer corners, near the head lamps. There will be some pin/clips retaining the bumper cover still, but separate easily without tools.

Nov 02, 2012 | 2005 Kia Rio

1 Answer

How do i remove the front bumper on a 2013 kia sorento


why take bumper off if your model was equipped for fog lights the wire plugs are already there as well the caps on the bumper should be screwed in place just go underneath and remove the caps and find the wires then put in a set of lights that fit in the hole or cut out the covers to fit your lights in saves a little of taking the bumper off

Sep 20, 2012 | Kia Sorento LX Cars & Trucks

1 Answer

Replace rio rear brake light bulb


1. Behind each light you will see a small door in the back liner. Remove the 2 plugs in each door by pulling them straight out.

2. Gently pull back liner doors to expose rear of light assembly.

3. Remove three brass 10mm nuts from exposed bolts.

4. Slightly lift up bottom inside corner of light assembly, Pull back or sideways to center of bumper or trunk rear with wiggle movement to pull out rear light assembly. Takes a little while, but piece of cake.

5. Plug in the new bulb and put everything back in place.

Dec 07, 2010 | 2004 Kia Rio

1 Answer

Want to replace bulb in dome ,removal of dome light casing on 2004 kia rio


just pull it down from the front its just clips....

Sep 12, 2010 | 2004 Kia Rio

1 Answer

How do i take the fuel pump out of a 2004 kia rio


remove the rear seat 2 12mm bolts in bottom on front then lift seat out you will see access panel fuel pump under there

Jul 10, 2009 | 2003 Kia Rio

1 Answer

2003 Kia Rio horn.


check driver side or passenger undernith front bumper inside bumper cover on frame. or check behind the grill.or by radiator

Jun 29, 2009 | 2003 Kia Rio

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...