Question about Cars & Trucks

Open Question

Front wheel stud removal 2007 Fortuner 4x4 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: 1990 Sentra How it remove and replace lug studs on front wheel

there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Posted on Feb 27, 2009

Ad
soc21610k
  • 215 Answers

SOURCE: I was trying to remove my front passenger tire & broke wheel stud

You just have to hammer it out. and rotate the hub so you can get it out. then put the new 1 on and tighten a lug on it till it's locked in

Posted on Jun 05, 2009

  • 176 Answers

SOURCE: Removal of broken wheel studs on 2004 saturn ion

The studs are pressed in and you need to use a big (mini sledge) hammer to knock them out. It will take a couple of good blows to push them out. To install the new ones, push the stud in from the back as far as it will go. Put some washers over the stud so that about 4 threads are present and lubricate the threads with bearing grease. Put your wheel nut on the stud and start to tighten the nut to the washers. This will pull the stud through so that the splined section will engage the hub assembly. Put more washers on if needed. Hope this helped.

Posted on Jun 16, 2009

ghost4548
  • 776 Answers

SOURCE: Front wheel stud broke off

Knuckle needs to be removed and the center hub 'pressed out' using a hydraulic press (accepted procedure). You can avoid this by using an air hammer and disk cutting tool to remove the old stud, then trim the 'stop flange' on the new stud (1/4 moon cut) in order to install it.... however, you gotta know what you're doing so you don't compromise the integrity of the new stud.

Posted on Jul 04, 2009

  • 39 Answers

SOURCE: Front wheel stud replacement for a 2006 Hyundai Sonata GL.

grind a flat spot on the round head of the new stud this should give enough clearance to install it. don't pull the hub this will damage the bearing.

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace right front wheel stud


If it is just one stud,it's best to leave it be,I have a 85 Nissan 4x4 and one stud is stripped and I have a repair manual and with it being a 4x4,there is a lot of parts to be remove to get to the stud and it may effect my 4x4ing if something doesn't go back just right.I found a repair guide for yours but it doesn't go into detail.It's best to have a repair manual for this so you will know how everything goes back.

Feb 08, 2013 | Nissan Cars & Trucks

1 Answer

My Toyota Fortuner 3l Diesel 4x4's central locking


Under the stearing wheel there is a fuse box on the left hand side, remove the pannel. Above the fuse box you will see a wiring harness with a box taped to it. Push all the cables in and test it while your doing it.

May 06, 2012 | 2006 Toyota Fortuner 3,0

1 Answer

I want to remove the front brake rotor from my 2000 gmc 4x4 3500. It looks like I have to remove the outer hub used to attach the wheels and also remove the spindle nut. After the 8 nuts and the spindle...


U use an air hammer with a pointy tool in it. Then u drive the lug studs out. The hub and rotor mate using the knurled area of the lug studs.

Feb 08, 2011 | 2000 GMC Sierra

1 Answer

Wheel stud removal, (front)


usally u bang it firt with a hammer then u have to get a special tool from your aouto part store (u can rent it) and then just take them off

Feb 08, 2010 | 2006 Hyundai Sonata

3 Answers

Broken stud on wheel


The studs press out and in. Perhaps a hammer would work. Replacements studs can be purchased. Need to remove hub, of course.

Aug 13, 2009 | Hyundai Motor 2003 Elantra

1 Answer

How to replace front broken wheel stud on a '02 jeep grand limited 4x4...steps involve to replace the bolt with a new one? thanks!


Remove wheel, brake caliper and rotor. Give the broken lug a good shot with a decent weight hammer and drive it out of the hub flange. Put new stud into hole, place a stack of washers on it and place the lug nut on backwards (flat side in)
Use oil on the threads to prevent binding, tighten lug 'till stud is seated, replace everything you removed.

Aug 11, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Having trouble with the removal fo the front rotor


soak around the hub and wheel studs with penetrating oil use a large hammer and a round punch work around the center of the rotor between the wheel studs until it pops free you can subtitute hammer and punch for an air chisel and round hammer head bit if available. don't hit the face of the rotor if your trying to save it.

Jul 24, 2009 | 2001 Jeep Grand Cherokee

1 Answer

I need to remove front r/side studs on 2005 hyundai elentra 4 dsd?


dear friend-replacing the stud is a fairly intensive job,the hub must be removed,so you might have to replace the wheel bearing,you will need special tools to attemp this job.

Jul 12, 2009 | 2007 Hyundai Sonata Limited Sedan

1 Answer

How do i remove front brake discs on my Lucida 4x4


Remove the front wheels. Remove the brake calipers (usually held with two stud bolts on the stub axle assembly.(look behind the disc)The discs should then pull off. On reassmbly ensure the caliper bolts are fully tightened.

Mar 05, 2009 | 1997 Toyota Previa

1 Answer

1994 GMC Suburban front hub / bearing removal


Knock the wheel studs through the assy.

Jun 09, 2008 | 1994 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...