Question about Cars & Trucks

Open Question

1998 Plymouth Grand Voyager SE

3.3L needs water pump replaced

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: transmission pump on a 98 plymouth voyager se

You should have a few special tools ready.
Fender to Fender Engine support.
Transmission Jack
A Lift would be real nice
Once the Trany is out it will be easy to remove the pump. It's putting the new one back in that can cause you some real headaches.

Posted on Dec 02, 2008

  • 4 Answers

SOURCE: WHERE IS THE WATER PUMP LOCATED ON A 1998 PLYMOUTH GRAND VOYAGER

Here are the steps required to change the water pump on the 3.0L engine.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.
To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50/50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.
34bef4a.jpg

Posted on Jan 20, 2009

  • 5 Answers

SOURCE: 1998 Plymouth Grand Voyager SE check engine light

it sounds like the transmission.take it to the shop and have then check the trasmission

Posted on May 17, 2009

canbruce75
  • 1776 Answers

SOURCE: How do you replace the water pump on a 3.3L 1998 Pymouth Grand Vy

Go to the autozone.com website and register. It's free and will give you access to an online repair manual. The steps for replacing the water pump can be found there. Hope this helped and best wishes.

Posted on Aug 11, 2009

Testimonial: "This is great information not only have you helped me with my current problem but, potential future problems as well. Thanks,"

  • 3640 Answers

SOURCE: how to change oil pump on plymouth grand voyager

go to http://www.autozone.com/autozone/homePage.jsp and sign up, put in your vehicles info and click on repair guides, they have oil pan remove and replace but no guide for the oil pump but its located in the oil pan and usually held on with 2 bolts and a gasket inside the pan, Tough job probably need someone with mechanical experience to help with this.

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

1 Answer

Belt squealing on a 1998 plymouth grand voyager 3.3 liter motor


have u checked the dampner pulley,it may b coming apart. if it only squeaks with the a/c on then it's your a/c clutch pulley.

Dec 04, 2011 | 1998 Plymouth Grand Voyager

1 Answer

How to change waterpump on a 99 plymoth grand voyager 3.3 motor


i need your help about problem water pump. I did exchanged new water pump. but it keep increase hot up .. i still figure something out about water pump. do you think fan cooling broke either fuse blow out .. thank you ..

Jan 17, 2010 | 1998 Plymouth Grand Voyager

2 Answers

How do you replace the water pump on a 3.3L 1998 Pymouth Grand Vy


Go to the autozone.com website and register. It's free and will give you access to an online repair manual. The steps for replacing the water pump can be found there. Hope this helped and best wishes.

Aug 11, 2009 | 1998 Plymouth Grand Voyager

1 Answer

1998 Plymouth Grand Voyager SE check engine light on and transmission shifts hard and will not shift into high.


it sounds like the transmission.take it to the shop and have then check the trasmission

May 17, 2009 | 1998 Plymouth Grand Voyager

2 Answers

WHERE IS THE WATER PUMP LOCATED ON A 1998 PLYMOUTH GRAND VOYAGER


Here are the steps required to change the water pump on the 3.0L engine.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.
To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50/50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.
34bef4a.jpg

Jan 12, 2009 | 1998 Plymouth Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...