Question about Cars & Trucks

Open Question

1990 nissan laurel c33. All fuses have power. Ignition has power but nothing intetior works.. Ie heater lights dash windows

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: my 1990 jeep cherokee dash lights fuse blows

it might not be that. check your headlamp relay. i know sounds weird but just do it. when i bought mine it had already been replaced with the wrong one so it kept blowing it and the radio. replaced with stock part and just like that no more problems. hope it helps

Posted on Aug 01, 2009

Ad
  • 7 Answers

SOURCE: power windows don't work at all for my 1990 Nissan 300ZX

check fuses first... that is a quick, easy, and very possible problem and luckily it isn't hard to do.
grab a volt meter or DMM and check to see if you have voltage coming in and then as you press check voltage on the rest of the plug on the switches. if you have nothing here is what i recommend.
remove the actual master switch and carefully take it apart down to the actual contacts (before very cautious not to break any of the plastic clips and watch for springs and small rollers inside the switch). look for carbon build up on the switch contacts and gently clean them with a small piece of fine grit sand paper. once all contacts are clean put everything back together and plug back into vehicle to test. repeat same process for passenger side if you are having issues on that side as well.
this is a standard process i go through anytime i buy an older vehicle.

Posted on Aug 18, 2009

  • 3 Answers

SOURCE: nissan sentra brake lights won't work

try the fuses

Posted on Aug 26, 2009

NismoMaster
  • 146 Answers

SOURCE: 2001 nissan altima dash lights

Nissan does not use inline fuse. You are looking for fuse number 34 (red 10 amp fuse). It is located under the hood between the engine and battery. Possibly marked "ILL"

Posted on Sep 07, 2009

  • 347 Answers

SOURCE: 1990 Camry Fuse Diagram. The following suddenly

REPLACE BUSTED FUSES

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i obtain a read out of the fault codes for the nissan c33 laurel


You can take it to a auto parts store if you live in the US . they will check for free . Or take it to a repair shop . or buy a code reader .

Sep 26, 2015 | Nissan Cars & Trucks

2 Answers

1990 hard body ignition relay just clicks no start and no power to dash components


If the starter solenoid clicks, tap the starter with a soft hammer.

Jul 26, 2015 | Cars & Trucks

1 Answer

92 plymouth voyager wont start and nothing work the windows wont go down the lock and unlock button does nothing idk what the problem is i had the battery tested and the battery is fine what would cause...


Nothing works? How about the headlights, do they work? If yes, then start checking all fuses in the Power Distribution Center or Box under the hood. If no, then look for a bad maxi-fuse in the PDC, and check for a bad fusible link between the battery and the PDC. The battery positive cable goes to the starter, but a pigtail lead off the positive would go to the PDC, to distribute power to all the various circuits on the car.
When you turn the key to on, does the dash light up? If yes, at least power is getting to, and going through the ignition switch. One could then check for power on the starter solenoid wire when key was held in crank or start position.
If nothing when turning key to on-no dash lights, nothing-then check for an ignition fuse in the PDC. If fuse is good check for power being available at the ignition switch connector. If no power there, check wiring between PDC and the ignition switch-if power is up to the switch, but nothing happens with key on, no dash or warning lights, then could have a bad ignition switch.
It just sounds like a maxi-fuse has blown, or a bad fusible link. Good luck.

Mar 18, 2013 | Cars & Trucks

1 Answer

1990 Isuzu Truck 2.6 5-Speed , Cranks but no fire to the plugs, new cap. rotor Turn key to ignition on and no check engine light, no heat/ac , no flashers. HELP!


OK several things to check, is there power to the fuel pump, check as close to pump as you can? and did you check the ignition coil?

Jun 09, 2012 | 1990 Isuzu Spacecab

1 Answer

Electrical problem


In most cases the fuse block is under the dash on the drivers side. In some vehicles I've seen them in the engine compartment.

Nov 19, 2009 | 1994 Nissan Pathfinder

1 Answer

Electrical problems


Sounds like you might have a bad ignition relay it id located above the fuse panel under the dash.

May 17, 2009 | 1990 Nissan 300ZX

1 Answer

Fuse problem


could be a wiring problem get a test light and test it

Sep 21, 2008 | 1990 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...