Question about 1996 Ford Ranger SuperCab

1 Answer

Ford truck xlt ranger2.3 litter oil in throttle body ? good or bad

It has a oil separator and im wondering if the hoses are connected right I already replaced a new pvc valve

Posted by on

  • johnnie69 Jul 15, 2013

    that was very helpfull and makes my day !!! im disabled due to a truckig accident and have particial brain damage so its nice to know someones out their with good thinking abilities mine our worn out thanks again!!!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 45 Answers

I found out with my old 94 Ranger 2.3L that the oil breather does not have a filter element, which causes oil to "naturally" (as Ford puts it) accumulate in the throttle body and air intake hose. You can get an inline breather element at any parts store for a few bucks and install it on the breather line without harming anything, and this will stop. Cheers.

Posted on Jul 15, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wyatt1582
  • 453 Answers

SOURCE: 1988 ford f150 running rough

Might want to change o2 sensor's, If they are not sending the right single its tell the computer to dump fuel. 1988 was using a fuel density system.
(1989 came out with Mass air flow system)
Check this
I think it might have a TFI module that's not working right. Located under distributor. Its gray and about 4" long and if equip, you need a 4 or 5.5 mm tool to unbolt it. This was a common thing back in the 80's. Its been so long I can't remember if the 4.9 straight 6 had it or not.
T- Thick
F- Film
I- Ignition module

Posted on Apr 24, 2009

vortash
  • 431 Answers

SOURCE: fuel pump

Hi I am Vortash you do seem to be having a few problems with this one , and it does sound a little like the fuel pump and ther is an easy way to check you are getting adequate pressure from the pump .. without a pressure meter .. take a small balloon ( you know the type hard to blow small and can cause you to bust a blood vessel trying to inflate them ideal for this ) place it over the end of the fuel pipe and tape it on tight .. remove the lead from the ignition coil so the vehicle will not start .. crank the vehicle and watch the ballon if it starts to inflate then the Pressure is fine . now dont forget this ballon will now be full of gasoline when you remove it so dont break it and have a bowl or. bucket handy .. and when you take it off also remember there is going to be a good deal of pressure in it ?.
Ok so if the ballon inflated the pump is ok if id didnt insist the garage do a fuel pressure test .
I have a cousin who works for Ford here in the UK it is 2.40 am in the morning here now so I will ask him tomorow or later today lol as I have heard of a fault like this before and it was not the fuel system but i want to check with him first .. Regards Vortash

Posted on May 29, 2009

housejess
  • 317 Answers

SOURCE: when I am in park or come to a complete stop at a

see if catalyc converter is clogged it will make a car idle and run bad

Posted on Nov 05, 2009

csmock132
  • 4669 Answers

SOURCE: A 1994 Ford Ranger, complete tuneup, new plugs,

Fuel injectors, sounds like on the bad

Posted on Mar 27, 2010

Testimonial: "thanks."

nighttrain_r
  • 444 Answers

SOURCE: engine missing on 1994 ford aerostar 3.0 v6

before throwing random parts at it do a compression check,

Posted on Mar 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Idiling high, temperature guage not working. no check engine light on. no problems shifting, fan coming off & on, blowing hot & cold air. can drive it, but it wont start up right away &


Check the cable to the temp sender unit is attached if so check the unit is working with a ohms meter. check the throttle cable is not binding ,the throttle leaver stop at the throttle body housing should be fully closed .

Mar 18, 2014 | 2005 Ford Escape XLT

1 Answer

Ford truck xlt ranger oil in throttle body ? good or bad


The most common cause is too much pressure in the crankcase. It could be bad piston rings, or a problem with the PCV system. The engine is supposed to draw fumes from the crankcase into the intake and burn them, but the intake may be getting real oil instead of just fumes.

Jul 14, 2013 | 1996 Ford Ranger SuperCab

2 Answers

Why would oil come thur pcv into trottle body


bad piston rings its coming with blowby gases

Dec 02, 2012 | 1991 Ford Ranger Supercab

2 Answers

Help! I have a 2004 Ford Explorer XLT Sport, V8.


try disconecting the battery for about 40min and leave the key in the on position while its disconected, turn off the key and reconnect the battery this will reset the ecu and may help your problem good luck and please rate

Aug 01, 2011 | 2004 Ford Explorer

1 Answer

Trouble code p2104 & p2112 for 2005 ford explorer xlt


There is a motor on the throttle body that opens it

It is called a Throttle Actuator Control Motor (TACM)

Those are the codes you got

DO NOT replace the throttle body

Spray the throttle plate with- CRC Throttle Body Cleaner

You should also have COP Ignition Coil-- Codes

A bad coil may be spiking the PCM,coming back
on the TPS and setting thoses codes

Mar 09, 2011 | Ford Explorer Cars & Trucks

1 Answer

Car shakes when it starts and trouble shifting gears


I HAD A FORD FOCUS AND THE PROBLEM WAS A MANIFOLD VACCUM LEAK AT THE HOSE THAT CONNECTS PCV VALVE TO INTAKE MANIFOLD. THIS HOSE CAN GET SATURATED WITH OIL AND COLLAPSE AND TEAR CAUSING A NO IDLE AND SHAKING CONDITION. IF THE CAR IS AN AUTOMATIC IT WILL HAVE TROUBLE SHIFTING BECAUSE OF INCORRECT RPM SIGNAL TO TRANS. CONTROL. ALL IS DUE TO VACCUM LEAK. ONE WAY TO FIND LEAK IS TO USE A SOLUTION OF DISH DETERGENT AND WATER IN A SPRAY BOTTLE AND SPRAY AREA AROUND AND BELOW THROTTLE BODY BELOW AIR CLEANER ASSY. ALSO LOOK FOR HOSE THAT ATTACHES AT MANIFOLD BELOW THROTTLE BODY AND BRANCHES OFF TO PCV VALVE SHOULD BE A "T" GOOD LUCK!!!!!!!!!

Oct 01, 2009 | 2001 Ford Focus

4 Answers

I have a 97 ford expedition 5.4 liter 4x4 that will start but won't continue to run. i have changed out the pump and it still acts as though it is fuel starved. I had just changed the oil and ran it for...


have you checked for vacuum leaks? thought mine was spark plugs and found broken vacuum hose attatchment behind throttle body to manifold was broken... that was my problem, maybe yours too? It's the hose just behind throttle body on passenger side- mine was a broken rubber elbow right at top of manifold- it's reachable without taking throttle body off...

Jun 03, 2009 | 1997 Ford Expedition

4 Answers

I have a 1988 ford bronco full size xlt it is ideling low when u


I just had the same issue with my 88 xlt w/351 W it wound up being the MAP sensor and the timing. I would check both of these and see if it solves your issue.

Feb 17, 2009 | 1988 Ford Bronco II

1 Answer

F-250 xlt 7.3L desiel


Yes, if theres coolingchannels running throgh the intake!

Aug 16, 2008 | 1992 Ford F250

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...