Question about Cars & Trucks

Open Question

Where is the timing mark on the camsprocket 1989 ford courier

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Louie_3006
  • 79 Answers

SOURCE: need timing marks ford ranger

The timing marks are on your timing belt cover. There is a little circle on the bottom right of the cover near the harmonic balancer that you can pop out to see if your distributor accesory gear is in the correct position. The camshaft has a triangle on the inside of the gear that you can line up with this accesory gear. The bottom of the timing belt cover has your timing tick marks and you may have to clean off this rectangular piece that is sticking out on the cover to see the marks. A good timing gun and remembering where the number 1 cylinder on your distributor is a good start to timing your motor. Refer to a Haynes Manual and it will give you a good guide line on how to time your motor with TDC. I hope you have good luck with this!

Posted on May 18, 2009

motor1258
  • 6674 Answers

SOURCE: timing marks for 1989 ford ranger

which engine?

Posted on Jul 18, 2009

  • 8 Answers

SOURCE: valve and camshaft timing marks 2003 2.6 lit

yeah

Posted on Jan 11, 2010

  • 4044 Answers

SOURCE: timming belt marks on ford

Normally I would give you a direct link to the Diagram you need but there isn't enough information in your post. Follow this link and when teh page comes up select the Serpentine Belt option which also shows you the Timing belts. You will need the Year, Make and model of vehicle. I highly recommend you get a Haynes or Chilton's Auto Repair manual on your vehicle to get the step by step instructions for lining everything up properly since you can actually lone the marks up Dead Center, 90 degrees out of time, 180 Degrees out of time and 270 degrees out of time if your not careful. Good Luck.

Posted on Jun 25, 2011

  • 5252 Answers

SOURCE: 2005 ford courier v6 sohc 4.0lt timing chain set up

Register for free at autozone.com, giving your make, year, and engine size.

They will have the diagrams for your ford, and quite a bit of repair information and procedures. Good luck.

Posted on May 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions to replace timing belt on a 1995 diesel ford courier


Hi,
REMOVAL
Disconnect the negative battery cable.
Remove accessory drive belt.
Remove the timing belt cover.
Align the timing mark on the camshaft sprocket with the timing mark on the cylinder head.
Confirm that the timing mark on the crankshaft sprocket is aligned with the timing mark on the oil pump housing.
Loosen the belt tensioner attaching bolt.
Pry the tensioner away from the timing belt and tighten the attaching bolt.
Remove the spark plugs.
Remove the RH engine mount and raise the vehicle.
Remove the splash shield.
Remove the crankshaft damper.
Remove the timing belt.

6_13_2012_3_43_16_pm.gif



INSTALLATION


Note: Do not mix 1/2 round and trapazoidal belt tooth profiles. This can cause premature belt wear, also the belt is meant to run in a dry environment. For maximum belt life, no oil or belt dressing compound should be applied to the timing belt.
Install the timing belt over the sprockets in a counterclockwise direction starting at the crankshaft. Keep the belt span from the crankshaft to the camshaft tight while installing over the remaining sprocket.
Loosen the belt tensioner attaching bolt, allowing the tensioner to snap against the belt.
CAUTION: Do not rotate crankshaft with the spark plugs installed .


Note: Do not turn the engine counterclockwise to line up the timing marks. After rotation, recheck camshaft timing marks for alignment. This will verify that the belt has not skipped a tooth during rotation.
Rotate the crankshaft clockwise two complete revolutions (720 degrees) stopping at top dead center. This will allow the tensioner spring to load the timing belt.
Tighten the belt tensioner attaching bolt to 23-30 Nm (17-22 lb-ft) .
Install the crankshaft damper.
Install the splash shield.
Lower the vehicle.
Install the RH engine mount.
Install the spark plugs.
Install the timing belt cover.
Install the accessory drive belt automatic tensioner.
Install the accessory drive belt.
Connect the negative battery cable.


Thank you.

Jun 13, 2012 | Ford Ranger Cars & Trucks

2 Answers

What are the timing chain marks on a 98 ford explore


zjlimited_1748.jpg

Fig. 19: Timing chain alignment - 4.0L engine (click image for zoom)

Hope this helps.

Aug 18, 2011 | 1998 Ford Explorer

1 Answer

How do i line up the timimg pulleys on a 89 toyota 2c motor? were are the marks? i can see one on the cam sprocket but not on the crank sprocket? is it the key notch on the end of the crack shaft?


No. The second timing mark will be found on the Oil Pump Housing. if you line the belt up with the timing mark on the camsprocket, and if need be use a guide string, and line it up with the Oin Pump Housing, you should be able to see it.

Hope this helps =)

Feb 21, 2011 | 1989 Toyota Camry

1 Answer

Where do you align timing marks on a 1989 ford ranger 2.3 liter


CLICK on the following LINK. It has the Timing Mark Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1989/make/ford/model/ranger/1989_ford_ranger_timing_belt_diagram_marks.htm

Feb 28, 2010 | 1989 Ford Ranger

1 Answer

Im changing the timing belt and I lost the position of the marks can some body tell me how to retime it its a 1989 ford ranger with a 2.3 ,,,, 5speed


Go to autozone.com and register for full free online repair manual.
Remember to time from #1 cylinder. Time marks are on crank pulley. When light flashes, the arrow should be closest to the -0- mark as possible

Sep 11, 2009 | 1989 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...