Question about Jeep Cherokee

1 Answer

Tran pan gasket

Cannot drop pan to cnge gasket..does ex pipe need to be dropped

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 85 Answers

Yes x pipe needs to be off or atleast loosened . And u might need new exhaust donuts . And heat will help take the bolts off

Posted on Jul 14, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 45 Answers

SOURCE: 98 Honda Civic EX Exhaust.

Donut gasket. You need 2 of them.

Posted on Aug 12, 2008

picatudo
  • 239 Answers

SOURCE: 1999 OIL PAN GASKET

you have to remove exhaust

Posted on Jan 05, 2009

  • 1 Answer

SOURCE: Trying to drop the oil

done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Posted on Apr 13, 2009

  • 462 Answers

SOURCE: OIL PAN GASKET LEAK

The engine has to be supported and the cradle under the engine has to be removed. After everything is reinstalled the front end has to be realigned.

Posted on Sep 13, 2009

Testimonial: "Thanks for your help, but i think i need a little more info. before tring this."

  • 4 Answers

SOURCE: changing oil pan gasket on 02 impala ls 3.8

The engine does have to be raised. The bolts are not easy to get to until the engine is lifted and the engine mount is removed. I'm doing this job right now and the book time is around 5 hours.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to put in a tranny filter on a 91 gmc 4x4 4.3l blazer


You remove the transmission pan and then remove the old filter. Make sure you remove the old seal out of the valve body and install new filter with new seal and re-install pan. Fill with fluid and you are done.

Nov 15, 2014 | Cars & Trucks

1 Answer

Oil pan gasket, is it metal or cork? There is a


0900c15280070826.jpg

Fig. Fig. 7: Always install a new oil pan gasket on a clean surface-V8 engine shown

  1. Remove the exhaust cross-over pipe.
  2. Remove the left engine-to-transmission strut.
  3. Remove the bolts and lower the oil pan.
  4. Thoroughly clean the gasket mating surfaces.
  5. When installing the pan, always use new gaskets coated with sealer. Apply a drop of RTV silicone sealer where the cork and rubber gaskets meet. On the 5.9L engine, make sure the gasket notches are positioned as shown. Tighten the oil pan bolts to 15 ft. lbs. (20 Nm). Tighten the cross-over pipe to 24 ft. lbs. (32 Nm). this is it no metal you can find this at auto zone libary

Oct 16, 2014 | Cars & Trucks

1 Answer

2001 Isuzu Trooper 4wd automatic trans. It will shift ou of 1st at about 20 mph into 2nd then loses power, rpm's drop until it slows to about 10mph then down shifts back to 1st. Any ideas why?


Sounds to me that your transmission is put itself into what is call (Limp Mode). This happens when the transmission fluid in the trans hydraulic valve body located on the bottom and in the trans pan are not within the parameters of the transmission computer. You can remove the trans pan and gasket to check for metallic material in the bottom of the pan. There is normally a strong magnet in the pan catch the material so I can't move freely through the transmission itself. It only takes a very small piece of foreign material to stop the flow of the valve body fluid. I would first take it to somewhere that had a automotive diagnostic scan tool that can read transmission codes to see if there are any active codes. Next you can drop the transmission pan yourself and look for material in it. Basically do a visually inspection and service the transmission fluid, gasket, and filter. Remember, all a automatic transmission is a extremely complicated fluid pump. If its pumping trans fluid properly it's probably working just fine. Been when the trans fluid gets hot, scorched, and stops moving. It will not work. Hope this helps

Nov 28, 2012 | 2001 Isuzu Trooper

2 Answers

How do i flush and change transmisson fluid on 2005 f-150


Make sure you have a BIG pan,drop the trans pan (messy job, start at the front and go around, finally leaving a couple of bolts in front in so the back drops down and drains from there). pull the trans filter off the bottom of the trans-make sure the o-ring comes off with the filter. clean the magnet a the bottom of the pan, reinstall it and the filter after you use lint-free rags to clean the bottom of the trans (valve body). You can usually just reinstall the pan with the original gasket, it is far superior to the junk they give you when you buy a kit with a filter (about $30 for the kit) and gasket. Dont over tighten the bolts, work in a cris-cross pattern until they all snug, then go 1/4 turn. Install a long funnel into the dipstick tube and fill it with about 10-11 quarts of Mercon 5-start it up, and if necessary, you may end up adding 1 or 2 more quarts to get it to levle.

Mar 08, 2011 | 2005 Ford F-150

1 Answer

In a 98 Mazda 626 2.0l a/t, where is the transmission filter and is it a filter or strainer? Can it be changed in the car?


its a filter inside trans need to drop pan to change but have to check which trans is in car the cd4e 4 spd auto trans is not serviceable requires some disassemble of trans the others are just drain drop pan replace filter replace gasket bolt pan back up fill

Jun 10, 2010 | 1998 Mazda 626

2 Answers

How much transmission fluid is required for a change?


Depending on what type of vehicle it can take as much as 16 to 18 quatrs of ATF , if you are completely flushing the unit. if you are just dropping the pan and draining it without flushing the torque converter then 12 qts. should be on the safe side, make sure you do not over fill or under fill the transmission, check level while trans is in nuetraul with parking brake set, wheels chalked. please rate my help , thanks

If you are dropping the pan be sure to install a new trans filter and pan gasket..

to have the unit professionally flushed by machine can cost as much as $ 200.00 with flush and filter change...

Aug 05, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Transmission oil


From what i can find out you have to take it to the shop

Jun 05, 2009 | 2006 Ford Explorer

1 Answer

Trans proublem


THE SHIFT SOLENOID NEEDS TO BE REPLACED EITHER INSIDE THE BOTTOM OF THE TRANSMISSION OR ON THE SIDE OF THE TRANS. I WOULD ALSO REPLACE THE TRANS FILTER WHILE THE PAN IS REMOVED. A TRANS FILTER KIT IS AVAILABLE AT MOST AUTO PARTS STORES WHICH INCLUDES A PAN GASKET. YOU WILL NEED ALMOST A GALLON(4 QTS.) OF TRANS FLUID TO FILL IT AFTER DROPPING THE PAN. HOPE THIS HELPS. BEST OF LUCK. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. PLEASE KEEP ME POSTED.

Apr 09, 2009 | 2002 Dodge Neon

1 Answer

98 Honda Civic EX Exhaust.


Donut gasket. You need 2 of them.

Jul 23, 2008 | 1998 Honda Civic

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...