Question about Cars & Trucks

Open Question

Emerson blower motors model#k55hxjms-9215 - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A.c. cooling fan runs constantly on high even with ignition off and key out


A/C - Heater blower motor ! What make , model and year vehicle ? Manual or automatic climate control ? Could be a bad blower motor control module , a high blow relay contacts stuck closed .

Mar 28, 2017 | Cars & Trucks

2 Answers

Blower motor and switch


What year , make and model ? Some new vehicles, well 2000 on up have body control modules that use a small amount of current to turn on a relay that turns on the blower motor that has a high amount of current.

Jan 12, 2015 | Cars & Trucks

1 Answer

My parking light brake come on when i turn on the


What is year--make--model? I can't track your wiring with out year, make, model.

Does the blower motor work at all? If you unplug the parking brake switch does the blower motor work, then?

Nov 23, 2014 | Cars & Trucks

1 Answer

Blower motor


I'm showing a blower relay and a resistor used on models with manual ac control.
The blower motor is grounded and the fan switch provides power thru the resistor. So you have a 40amp blower fuse that handles high thru the relay, then a 30amp HVAC fuse that powers the blower thru the fan switch.
Do you not have power from the resistor to the blower motor on the purple wire ?

Jun 26, 2013 | 2003 GMC Envoy

1 Answer

How do i change a blower motor in a ford tempo 1992? i have the blower motor lose but the bottom og the glove box bar is in my way. how do i take that out to get the motor out?


Less Air Conditioning

  1. On models equipped with airbag, disarm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. Disconnect battery ground cable.
  3. Remove screws securing right ventilator control cable to instrument panel.
  4. Remove screw securing right register duct to lower right edge of instrument panel.
  5. Remove glove box and hinge bar from instrument panel.
  6. Pull right register duct from installed position between air inlet duct and right register opening, Fig. 10.
  7. Remove ventilator grille from bottom of ventilator assembly, then screws securing right ventilator assembly to blower housing.
  8. Remove hub clamp spring from blower wheel hub, Fig. 11.
  9. Pull blower wheel from blower shaft, then remove three blower motor flange attaching screws.
  10. Pull blower motor from housing, disconnect electrical connector, then remove motor from vehicle.
  11. Reverse procedure to install.
  12. On models equipped with airbag, rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
With Air Conditioning

  1. On models equipped with airbag, disarm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. Disconnect battery ground cable.
  3. Remove glove box door and instrument panel lower reinforcement from instrument panel.
  4. Disconnect blower motor electrical connector, then remove blower motor and mounting plate from evaporator housing.
  5. Rotate motor until mounting plate flats clear edge of glove box opening, then remove motor.
  6. Remove hub clamp wheel spring from blower wheel hub and remove blower wheel from motor shaft.
  7. Reverse procedure to install.
  8. On models equipped with airbag, rearm airbag system as described underMAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.

Dec 18, 2010 | 1992 Ford Tempo

1 Answer

AC or heater fan does not work?


The most common problem with these fans are the fan itself wears out, or the relay becomes burnt at the contacts inside, or both.

Blower Motor REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If necessary on 1992 and 1993 Typhoons, remove the charge air cooler. For details, please refer to Section 3 of this manual. Fig. 1: Example of a common blower motor installation - vehicles without A/C shown 85386001.gif

  3. Disconnect the blower motor cooling tube.
  4. Disengage the electrical connector(s) from the blower motor, as necessary. NOTE: On some earlier models equipped with A/C, it may be necessary to disconnect the A/C vacuum tank and move it aside.
  5. Remove the blower motor-to-case screws, then carefully withdraw the blower motor from the case. To install:
  6. Install the blower motor to the case and secure using the retaining screws.
  7. Engage the electrical connector(s) to the motor, as necessary.
  8. If moved on early model vehicles, reposition and secure the A/C vacuum tank.
  9. Connect the blower motor cooling tube.
  10. If removed on 1992 and 1993 Typhoons, install the charge air cooler.
  11. Connect the negative battery cable. Fig. 2: Disconnect the blower motor cooling tube 86616001.jpg
    Fig. 3: Disengage the necessary electrical connector(s) from the blower motor 86616002.jpg
    Fig. 4: Loosen and remove the blower motor retaining screws 86616003.jpg
    Fig. 5: Withdraw the blower motor from the case 86616004.jpg
prev.gif next.gif

Nov 19, 2010 | 1991 Oldsmobile Bravada

2 Answers

Where is the blower motor located on a 91 Dodge Dakota and how do I access it?


Blower Motor REMOVAL & INSTALLATION Dakota
  1. Disconnect the negative battery cable.
  2. Remove the steering column cover, intermittent wiper control and the lower instrument panel module retaining screw to the right of the steering column.
  3. Remove the center distribution duct retaining screws and panel support screw at the bottom of the module. Fig. 1: Heating/air conditioning unit components - Dakota models 88476g01.gif

  4. Remove the courtesy lamp at the lower right corner of the module and the screw near the ash receiver.
  5. Open the glovebox and remove the screws along the top edge.
  6. Move the module out and down far enough to unclip the wiring harness and antenna cable and disconnect the speaker wire (if equipped with monaural radio) and glovebox light wire. Remove the module from the vehicle.
  7. If the vehicle is equipped with air conditioning, disconnect the two vacuum lines from the recirculating air door actuator and disconnect the blower lead wires.
  8. Remove two screws at the top of the blower housing, five screws from around the housing and remove the blower housing from the unit.
  9. Remove three screw attaching the blower to the unit and remove the blower from the vehicle.
  10. Remove the fan from the blower motor.
  11. Installation is the reverse of removal. Secure all components accordingly and check the blower motor for proper operation.
Pick-Up and Ramcharger
  1. Disconnect the negative battery cable.
  2. Disconnect the blower wiring. Fig. 2: Exploded view of the heater assembly components for Pick-up and Ramcharger models 88476g00.gif

  3. Remove the blower motor cooling tube. Fig. 3: Disconnect the wiring and cooling tube to access the blower motor - 1994-96 models shown 88476g06.gif

  4. Remove the screws or retaining nuts retaining the blower plate to the housing. Fig. 4: Unplug the wiring harness connector to the blower motor 88476p14.jpg
    Fig. 5: Unfasten the blower plate housing screws 88476p15.jpg

  5. Remove the assembly from the housing. Fig. 6: Lift away the blower plate housing for access to the blower motor 88476p16.jpg

  6. Remove the spring clip fastening the blower wheel to the blower shaft and pull off the wheel. Remove the blower from the plate. Fig. 7: Unclip and remove the blower wheel 88476p17.jpg

  7. Installation is the reverse of removal.
prev.gif next.gif

Oct 14, 2010 | 1991 Dodge Dakota

1 Answer

Blower motor doesnt work at all..getting no pwer to the blower motor or switch


Check the fuse for the blower motor,and the relay.The relay maybe in with the resister on this model,it is located near the blower motor.

Feb 09, 2010 | 2004 Ford F250

1 Answer

Blower motor


PART 1
If all blower speeds are not working I would check the blower, but if only one speed is not working I would check the resistor block for the blower it controls the speeds. they use 2 different blowers in this truck I have to sent a second message with the rest it will not hold it all inthis message.

2001–05 Models With Delphi Blower Motor
  1. If equipped, remove the sound insulator panel.
  2. Remove the blower motor insulating cover screws.
  3. Disconnect the electrical connector from the blower motor.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor from the heater/ventilation module.
  6. Remove the blower motor.
c93043c.jpgPull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor

To install:
  1. Install the blower motor.
  2. Install the blower motor to the heater/ventilation module. Turn the blower assembly clockwise until the retaining tab locks into place.
  3. Install the blower motor insulating cover.
  4. Connect the electrical connector to the blower motor.
  5. Install the blower motor insulating cover screws.
    1. Tighten the screws to 14 inch lbs. (1.6 Nm).
  6. If equipped, install the sound insulator panel

Nov 27, 2008 | 2004 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...